【正文】 at is also in the top of the steel wheel is raised outside, and then tighten the knob. The next step is to use his hands and promote activity in the fastener rod, to make CARDS in the wheels can card arm, then hang security within the tattoo hook, check fixtures is installed firmly. Three, installation controller is equipped: According to the corresponding four sensors installed to the wheels of the fixture position. Should pay attention to in the positioning shaft sensor to daub sparse of lubricating oil (cannot besmear butter), in order to prevent the long time after insertion caused wear, can39。t accurate positioning shaft installed in place, affect the measurement precision. Connecting munication cable and Angle to disk cables. The arrow on the cable plug sockets and of the arrow after, you can directly inserted. Four cable length of the difference just is different, the two root meters cable is used for connecting controller is equipped with two front39。s sensors, two meters in the cable is mutual connection. Before and after sensor Each sensor has three socket, above two are the same, the one below is used for connecting corner plates. Cable connection good after, unplug corner after the plate and skateboard fixed pin. Give the vehicle lifting the lowest lift down the safety lock up the grid position, in order to ensure lifting platform in horizontal status. On the sensor and controller is equipped power indicator, press R key or the corresponding position key activation each sensor, after the sensor is put on the level of fixed the knob, tighten the bubble in roughly the level of position. Four, operation controller is equipped: Boot after, batch program will automatically into measurement procedures for user39。s initial status for the next step, the operation. According to move to the next step can be F3 keys. Screen TEST, said that the system was refreshed memories of last measurement information. Then program started measuring steps. Step four main points measuring steps, the first is the measure, including preparation of the input registration forms, select models and deviation of pensation. Input the registration form: contains various customer information, can choose any want to input project, and the future of the project can be according to the input to mix the measurement results data. PaiZhaoHao or maintenance, can generally vehicles single Numbers to enter the corresponding entries for future submitted. Input information can be English letters and Numbers, no Chinese character input. Fill out the form, by F3 after entering models choose interface. Choose the corresponding to the test vehicle models, if need to do after deviation of pensation, then the advance, or press F4 F3 stop. With deviation pensation: if the fixture is used, the only one in rapid fixture serious damage degree when straps, they need to do with deviation pensation (for PassatB5 AudiA6 or before must do, measurement for deviation pensation)。 If the use of peeling, the fixture since for all vehicles must do with deviation pensation. Do the deviation of pensation points: (1) tire rotation direction should be vehicles moving direction of rotation. (2) adjustment before detection: installed controller is equipped with brakes locked. Equipment Enter adjustment before detecting steps, steering wheel will appear on the screen to it pattern. In the green area, says acceptable range, but on both sides of the green range around the measurement results, can differ about five points. Therefore, it is best to in the green zone of arrows in the middle in the black. The steering wheel in the order: first, then turn right, then left 20 degrees to 20 degrees, then. Measured at the screen when the front wheel beam. According to measurements F3 button to enter the maximum rotation Angle plate, using electronic steps through the steps the controller is equipped can be automatic measure the maximum total corner. Firstly, then according to the steering wheel in errov screen, remove both front sensor. Stay screen displays the measured, after waiting for picture to the right until the steering wheel continuous play motionless, then a steady living so far not let go. Wait until after continuous measurement to the right, then play the steering wheel so until dozen don39。t move, and then a steady living not let go. Wait until after the end of automatic measurement, screen showed all the measurement data. Reload the two front sensor, if measured data, adjustable scope of more than allow the data, it can adjust steps into position.Positioning adjustment: do positioning adjustment before, first with a steering wheel lock will steering wheel fixed into horizontal rises again to proper adjustment of lifting machine, will lift high level security position in the lock. Adjusted for four sensors horizontal status, then operate controller is equipped into position adjustment operation. Adjust program will first display vehicles the measured value of the rear axle a parameters, if vehicle rearaxle parameters is adjustable (most vehicles rearaxle positioning parameter is unable to adjust), then the screen can consult to adjust, screen data at the data will display the current adjusted parameters data. Rearaxle positioning parameters adjustment, by F3 after may enter front axle tuning steps. Camber Angle adjustment psn according to the structure of the vehicle chassis, can be divided into two kinds, one kind is need to lift shaft can be adjusted to front wheel impending camber Angle。 Another kind is need not lifting front axle camber Angle can be adjusted. The need for lifting the front axle camber Angle adjustment, its position adjustment of vehicle steps as follows: 1) according to the screen F3 key until psn adjust the picture. This screen also showed that the front axle of the five positioning parameter values, they were: left, right wheel, left, right, camber Angle front wheel bundle, total before former bea