汽車技術雜志xxxx年第5期目次及摘要-中國汽車工程-資料下載頁
2025-06-25 11:58本頁面
【正文】 engine with no catalytic converter, PM emission of diesel fuel with sulfur content approx. 273106 is reduced by % as pared with diesel fuel with sulfur content approx. 800106。 to meet Euro III emission standard, the key in the development of electronicallycontrolled diesel engine with no tail gas aftertreatment device is to develop diesel engine bustion system and control lubrication oil consumption.Key words: Sulfur content。 Diesel engine。 PM emission電控噴射單一燃料CNG轎車發動機的性能試驗張群1，2 王天友1 吳喜慶1，2 郭云杰1 王剛德1 付曉光1李 琦2 劉書亮1（；）【摘要】研究了過量空氣系數及點火時刻對某電控噴射單一燃料壓縮天然氣發動機的動力性、經濟性和排放性能的影響。試驗結果表明，在整個轉速范圍內，%，%。在此基礎上得到了在變過量空氣系數和點火時刻下，該天然氣發動機的燃燒、排放規律。主題詞：壓縮天然氣發動機 過量空氣系數 點火時刻 性能試驗Performance Test of CNG Car Engine featuring Electronicallycontrolled InjectionZhang Qun1,2, Wang Tianyou1, Wu Xiqing1,2, Guo Yunjie1, Wang Gangde1, Fu Xiaoguang1, Li Qi2, Liu Shuliang1(1. State Key Laboratory of Internal Combustion Engines, Tianjin University。 2. Tianjin FAW Xiali Automobile Co., Ltd)【Abstract】The effect of excessive air coefficient and ignition timing on dynamic performance, fuel economy and emission performance of an electronically controlled injection dedicated CNG car engine was studied. The test results show that the engine’s BSFC is about % lower and effective thermal efficiency is % higher as pared to gasoline engine. Based on this, the law of bustion and emission of CNG engine is obtained under variable excessive air coefficient and ignition timing.Key words: CNG engine。 Excessive air coefficient。 Ignition timing。 Performance test基于UG的車身點云數據快速對齊方法高尚鵬 徐家川 李迪 （山東理工大學）【摘要】根據圖形坐標變化理論，提出了基于UG點擬合法的汽車車身點云數據坐標快速對齊方法，介紹了點擬合法的坐標變化理論及汽車車身坐標系與UG系統坐標系的對齊方法。結合工程實例，利用點擬合法快速準確地實現了車身點云數據的坐標對齊，驗證了該方法的有效性。主題詞：車身 點云數據 擬合方法The Rapid Alignment Method of Point Cloud Data for Auto Body based on UGGao Shangpeng, Xu Jiachuan, Li Di (Shandong University of Technology)【Abstract】In accordance with graphic coordinate change theory, the rapid alignment method of point cloud data for autobody based on the UGpoints fit method is presented in the paper, in which the coordinate change theory of point fit method and the alignment method of autobody coordinate and UG system coordinate system are introduced. It takes engineering example to use the point fit method to align the coordinate of autobody point cloud data quickly and correctly. The result verified effectiveness of this method.Key words: Autobody。 point cloud data。 fit method基于數字化工廠的白車身焊裝前期規劃寧宇1,2 韓英淳1 李悅2（；）【摘要】以某企業B車型主焊線規劃為例，對數字化工廠技術在其白車身焊裝線前期規劃中的應用進行了闡述。介紹了基于數字化工廠的白車身焊裝解決方案及前期規劃的內容、流程和實施方法。由于在前期規劃中進行了焊點可達性分析、機器人仿真分析和干涉檢查等，因而大大縮短了各工位夾具與抓具的設計時間并提高了準確率，顯著減少了后期修改工作量。主題詞：白車身 數字化工廠 焊裝線 前期規劃Advanced Planning of BIW Welding based on Digital FactoryNing Yu1,2, Han Yingchun1, Li Yue2(1. Jilin University。 2. FAW Mould Manufacturing Co., Ltd)【Abstract】With the welding line planning of vehicle model B of a pany as example, the paper elaborates the application of digital factory technology in BIW welding line advanced planning. The paper introduces BIW welding solution based on digital factory as well as content, flow and implementation of advanced planning. Since welding spot reachability analysis, robot simulation analysis and interference check, etc., are conducted in the advanced planning, therefore the design time of jig and gripper are shortened, accuracy rate is improved, modification work in the later stage is considerably reduced.Key words: BIW。 Digital factory。 Welding line。 Advanced planning17 / 17
畢業設計相關推薦
鄂ICP備17016276號-1