【正文】 orrected and controlled，應表述為 可糾正或可控制可糾正或可控制 的因素EConsider human error, wearout of tools, ambient conditions, and interactions of factors，如人的過失，工裝磨損、環境條件以及因素間的相互作用PFMEAw Causes of failure often show up as a chain of events, from immediate cause to root cause失效通常是由一連串的原因造成的，從直接原因到根本原因w It is remended that these chains be developed for each failure mode and recorded on the FMEA form建議針對每一種失效模式，找出原因鏈，記入 FMEA表Euse a tree or fishbone diagram to develop可利用樹形圖或魚刺圖8. Cause(s) of Failure失效原因PFMEA 9. Assess the likelihood of occurrence of each cause評估每種失效原因產生的可能性w Use historical data (as a baseline) ，利用歷史資料E Take improvements into account，并考慮所作的改進 w Use statistical models and parison with similar processes利用可靠性模型，與類似的過程進行比較PFMEA910 Failure almost inevitable，失效幾乎不可避免78 Similar processes that have often failed in the past，以前類似過程常常失效46 Similar processes that have occasional failures，類似過程偶爾失效13 Similar processes that have experienced isolated failures，類似過程僅有過個別失效9. Assess the likelihood of occurrence of each cause評估每種失效原因產生的可能性PFMEA Occurence (O)Probability Likely Failure Rates*　 Very High: Persistent Failures= 100 per thousand piecesVery High: Persistent Failures 50 per thousand piecesHigh: Frequent Failures 20 per thousand pieces　 High: Frequent Failures 10 per thousand pieces　 Moderate: Occasional Failures 5 per thousand piecesModerate: Occasional Failures 2 per thousand pieces　 Moderate: Occasional Failures 1 per thousand pieces　 Low: Relatively Few Failures per thousand pieces　 Low: Relatively Few Failures per thousand pieces　 Remote: Failure is Unlikely= per thousand pieces10987654321PFMEA Causes and EffectsHarness ClampCauseandeffect chainradius out of spectool is worntool notreplacedlack of maintenance procedureclamp cracksat bendbundle falls outrattling noiseCAUSE chainEFFECT chainPFMEA Causes and EffectsWiring AssemblyEffects TreeCrossed Wire NofunctionFire in PlantOperatorInjuryDamagedEquip.Must repair vehiclePFMEA Causes and EffectsWiring AssemblyCauses TreeCrossed WireBoardErrorOperatorErrorPoorInstruct.NottrainedOper istiredPFMEA 10. List the Current Process Controls列出現有過程控制w Process controls catch the defect before the product reaches the customer，過程控制當在產品到達顧客前發現缺陷 !w There are three Types of process controls, 過程控制有三種類型 : (1) prevent the cause of failure, or reduce the rate of occurrence，防止原因出現或降低其出現的可能性 (2) detect the cause(s) of failure and lead to corrective actions，查明失效的原因并找出糾正措施 (3) detect the failure mode(s)，檢測失效模式PFMEAw Assign currently used process controls to failure modes and causes，針對失效模式或原因列出現行的過程控制手段EUsed on similar processes in the past，以前類似過程如何控制ECan be of any Type: 1, 2, or 3, or any bination，可以是 3類或其組合EType 1 controls affect the likelihood of occurrence, if already part of the design，若設計中已有體現，則第 1類方法可降低原因出現的頻度EIf none, write “None” ，若沒有，則填 “無 ”。PFMEAProcess Failure Mode and Effects Analysis過程失效模式及后果分析 (PFMEA)PFMEAPFMEA陶 國PFMEA Proprietary Information專有信息w Your FMEA (Control Plan, Process Capability, etc.) may be considered proprietary and should not be shared with anyone outside the division without first consulting your management. FMEA (控制計劃、過程能力等 ) 可視為專有信息，在未事先 征得管理部門同意之前，不得向部門以外的任何人透露。10. List the Current Process Controls列出現有過程控制PFMEAw Detection is an assessment of the probability that，探測度為下列事件發生的概率Ea type 2 control can detect the cause and lead to corrective action, 第 2類控制能夠發現原因并找到糾正措施 Ea type 3 control can detect a failure，第 3類控制能夠在不良品到達顧客前發現缺陷... before the product reaches the customer!Edetection can also assess how effectively a type 1 control can prevent failure，第 1類控制能夠預防失效的有效程度11. Detecting failure探測度PFMEA 11. Detecting failure探測度Detecti