【正文】 igh rate of oxidation and the danger of fire (the element is pyrophoric).Molybdenum is ductile and workhardening, so it can produce poor surface finish. Sharp tools are necessary.Nickelbased alloys are workhardening, abrasive, and strong at high temperatures. Their machinability is similar to that of stainless steels.Tantalum is very workhardening, ductile, and soft. It produces a poor surface finish。 tool wear is high.Titanium and its alloys have poor thermal conductivity (indeed, the lowest of all metals), causing significant temperature rise and builtup edge。 they can be difficult to machine.Tungsten is brittle, strong, and very abrasive, so its machinability is low, although it greatly improves at elevated temperatures.Zirconium has good machinability. It requires a coolanttype cutting fluid, however, because of the explosion and fire. Machinability of Various MaterialsGraphite is abrasive。 it requires hard, abrasionresistant, sharp tools.Thermoplastics generally have low thermal conductivity, low elastic modulus, and low softening temperature. Consequently, machining them requires tools with positive rake angles (to reduce cutting forces), large relief angles, small depths of cut and feed, relatively high speeds, and proper support of the workpiece. Tools should be sharp.External cooling of the cutting zone may be necessary to keep the chips from being “gummy” and sticking to the tools. Cooling can usually be achieved with a jet of air, vapor mist, or watersoluble oils. Residual stresses may develop during machining. To relieve these stresses, machined parts can be annealed for a period of time at temperatures ranging from to (to), and then cooled slowly and uniformly to room temperature.Thermosetting plastics are brittle and sensitive to thermal gradients during cutting. Their machinability is generally similar to that of thermoplastics.Because of the fibers present, reinforced plastics are very abrasive and are difficult to machine. Fiber tearing, pulling, and edge delamination are significant problems。 they can lead to severe reduction in the loadcarrying capacity of the ponent. Furthermore, machining of these materials requires careful removal of machining debris to avoid contact with and inhaling of the fibers.The machinability of ceramics has improved steadily with the development of nanoceramics (Section ) and with the selection of appropriate processing parameters, such as ductileregime cutting (Section ).Metalmatrix and ceramicmatrix posites can be difficult to machine, depending on the properties of the individual ponents, ., reinforcing or whiskers, as well as the matrix material. Thermally Assisted MachiningMetals and alloys that are difficult to machine at room temperature can be machined more easily at elevated temperatures. In thermally assisted machining (hot machining), the source of heat—a torch, induction coil, highenergy beam (such as laser or electron beam), or plasma arc—is forces, (b) increased tool life, (c) use of inexpensive cuttingtool materials, (d) higher materialremoval rates, and (e) reduced tendency for vibration and chatter.It may be difficult to heat and maintain a uniform temperature distribution within the workpiece. Also, the original microstructure of the workpiece may be adversely affected by elevated temperatures. Most applications of hot machining are in the turning of highstrength metals and alloys, although experiments are in progress to machine ceramics such as silicon nitride. SUMMARYMachinability is usually defined in terms of surface finish, tool life, force and power requirements, and chip control. Machinability of materials depends not only on their intrinsic properties and microstructure, but also on proper selection and control of process variables.譯文： 可機加工性一種材料的可機加工性通常以四種因素的方式定義： 分的表面光潔性和表面完整性。刀具的壽命。切削力和功率的需求。切屑控制。以這種方式，好的可機加工性指的是好的表面光潔性和完整性，長的刀具壽命，低的切削力和功率需求。關于切屑控制，細長的卷曲切屑，如果沒有被切割成小片，以在切屑區變的混亂，纏在一起的方式能夠嚴重的介入剪切工序。因?yàn)榧羟泄ば虻膹?fù)雜屬性，所以很難建立定量地釋義材料的可機加工性的關系。在制造廠里，刀具壽命和表面粗糙度通常被認為是可機加工性中最重要的因素。盡管已不再大量的被使用，近乎準確的機加工率在以下的例子中能夠被看到。 鋼的可機加工性因?yàn)殇撌亲钪匾墓こ滩牧现唬ㄕ绲?章所示），所以他們的可機加工性已經被廣泛地研究過。通過宗教鉛和硫磺，鋼的可機加工性已經大大地提高了。從而得到了所謂的易切削鋼。二次硫化鋼和二次磷化鋼 硫在鋼中形成硫化錳夾雜物（第二相粒子），這些夾雜物在第一剪切區引起應力。其結果是使切屑容易斷開而變小，從而改善了可加工性。這些夾雜物的大小、形狀、分布和集中程度顯著的影響可加工性。化學元素如碲和硒，其化學性質與硫類似，在二次硫化鋼中起夾雜物改性作用。鋼中的磷有兩個主要的影響。它加強鐵素體，增加硬度。越硬的鋼，形成更好的切屑形成和表面光潔性。需要注意的是軟鋼不適合用于有積屑瘤形成和很差的表面光潔性的機器。第二個影響是增加的硬度引起短切屑而不是不斷的細長的切屑的形成，因此提高可加工性。含鉛的鋼 鋼中高含量的鉛在硫化錳夾雜物尖端析出。在非二次硫化鋼中，鉛呈細小而分散的顆粒。鉛在鐵、銅、鋁和它們的合金中是不能溶解的。因?yàn)樗牡涂辜魪?qiáng)度。因此，鉛充當固體潤滑劑并且在切削時，被涂在刀具和切屑的接口處。這一特性已經被在機加工鉛鋼時，在切屑的刀具面表面有高濃度的鉛的存在所證實。當溫度足夠高時—例如，在高的切削速度和進刀速度下—鉛在刀具前直接熔化，并且充當液體潤滑劑。除了這個作用，鉛降低第一剪切區中的剪應力，減小切削力和功率消耗。鉛能用于各種鋼號，例如10XX，11XX，12XX，41XX等等。鉛鋼被第二和第三數碼中的字母L所識別（例如，10L45）。（需要注意的是在不銹鋼中，字母L的相同用法指的是低碳，提高它們的耐蝕性的條件）。然而，因?yàn)殂U是有名的毒素和污染物，因此在鋼的使用中存在著嚴重的環境隱患（在鋼產品中每年大約有4500噸的鉛消耗）。結果，對于估算鋼中含鉛量的使用存在一個持續的趨勢。鉍和錫現正作為鋼中的鉛最可能的替代物而被人們所研究。脫氧鈣鋼 一個重要的發展是脫氧鈣鋼，在脫氧鈣鋼中矽酸鈣鹽中的氧化物片的形成。這些片狀，依次減小第二剪切區中的力量，降低刀具和切屑接口處的摩擦和磨損。溫度也相應地降低。結果，這些鋼產生更小的月牙洼磨損，特別是在高切削速度時更是如此。不銹鋼 奧氏體鋼通常很難機加工。振動能成為一個問題，需要有高硬度的機床。然而，鐵素體不銹鋼有很好的可機加工性。馬氏體鋼易磨蝕，易于形成積屑瘤，并且要求刀具材料有高的熱硬度和耐月牙洼磨損性。經沉淀硬化的不銹鋼強度高、磨蝕性強，因此要求刀具材料硬而耐磨。鋼中其它元素在可機加工性方面的影響 鋼中鋁和矽的存在總是有害的，因?yàn)檫@些元素結合氧會生成氧化鋁和矽酸鹽，而氧化鋁和矽酸鹽硬且具有磨蝕性。這些化合物增加刀具磨損，降低可機加工性。因此生產和使用凈化鋼非常必要。根據它們的構成，碳和錳鋼在鋼的可機加工性方面有不同的影響。低碳素鋼（%的碳）通過形成一個積屑瘤能生成很差的表面光潔性。盡管鑄鋼的可機加工性和鍛鋼的大致相同，但鑄鋼具有更大的磨蝕性。刀具和模具鋼很難用于機加工，他們通常再煅燒后再機加工。大多數鋼的可機加工性在冷加工后都有所提高，冷加工能使材料變硬并且減少積屑瘤的形成。其它合金元素，例如鎳、鉻、鉗和釩，能提高鋼的特性，減小可機加工性。硼的影響可以忽視。氣態元素比如氫和氮在鋼的特性方面能有特別的有害影響。氧已經被證明了在硫化錳夾雜物的縱橫比方面有很強的影響。越高的含氧量，就產生越低的縱橫比和越高的可機加工性。選擇各種元素以改善可加工性，我們應該考慮到這些元素對已加工零件在使用中的性能和強度的不利影響。例如，當溫度升高時，鋁會使鋼變脆（液體—金屬脆化，熱脆化，），盡管其在室溫下對力學性能沒有影響。因?yàn)榱蚧F的構成，硫能嚴重的減少鋼的熱加工性，除非有足夠的錳來防止這種結構的形成。在室溫下，二次磷化鋼的機械性能依賴于變形的硫化錳夾雜物的定位（各向異性）。二次磷化鋼具有更小的延展性，被單獨生成來提高機加工性。 其它不同金屬的機加工性盡管越軟的品種易于生成積屑瘤，但鋁通常很容易被機加工，導致了很差的表面光潔性。高的切削速度，高的前角和高的后角都被推薦了。有高含量的矽的鍛鋁合金鑄鋁合金也許具有磨蝕性，它們要求更硬的刀具材料。尺寸公差控制也許在機加工鋁時會成為一個問題，因?yàn)樗信蛎浀母邔?dǎo)熱系數和相對低的彈性模數。鈹和鑄鐵相同。因?yàn)樗吣ノg性和毒性，盡管它要求在可控人工環境下進行機加工?；诣T鐵普遍地可加工，但也有磨蝕性。鑄造無中的游離碳化物降