第八章ad轉換模塊-在線瀏覽
2024-09-11 13:22本頁面
【正文】 應用 ?單通道，單次轉換 ?多通道，單次轉換 ?單通道，序列轉換模式 ?多通道，序列轉換模式 ?特殊通道測試模式 ADC 工作方式 27 單片機原理與應用 ATD Registers 7/12 ATD Status Register 0 (ATDSTAT0) SCF Sequence Complete Flag 0=Conversion sequence not pleted 1=Conversion sequence has pleted ETORF External Trigger Overrun Flag 0=No External trigger over run error has occurred 1=External trigger over run error has occurred FIFOR Result Register Over Run Flag 0=No over run has occurred 1=Overrun condition exists (result register has been written while associated CCFx flag was still set) CC[3:0] Conversion Counter 當前轉換結果將寫入的結果寄存器編號 例如： CC[3:0]=0110， 轉換結果寫入第 6個結果寄存器 先入先出模式下，不被初始化，當計數到最大值回最小值 非先入先出模式下，轉換開始和結束時被初始化為 0 兩種模式下終止 ATD轉換或開始新 ATD轉換均被清零 28 單片機原理與應用 ATD Registers 8/12 ATD Compare Enable Register (ATDCMPE) CMPE[15:0] Compare Enable for Conversion Number n (n= 15, 14, 13, 12, 11, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0) of a Sequence 0=No automatic pare 1= Automatic pare of results for conversion n of a sequence is enabled 對一個序列中第 n次 ATD轉換結果進行比較，除 CMPE[n]=1，還要完成如下設置： ① 將比較閾值寫入 ATDDRn ② 寫 ATDCPMHT的 CMPHT[n]位選擇比較方法 注：寫 ATDCMPE會終止當前轉換序列 29 單片機原理與應用 ATD Registers 9/12 ATD Status Register 2 (ATDSTAT2) CCF[15:0] Conversion Complete Flag n (n= 15, 14, 13, 12, 11, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0) 0=Conversion number n not pleted or successfully pared 1=If (CMPE[n]=0): Conversion number n has pleted. Result is ready in ATDDRn. If (CMPE[n]=1): Compare for conversion result number n with pare value in ATDDRn, using pare operator CMPGT[n] is true. (No result available in ATDDRn) 出現以下任一情況， CCF[n]被清零： ① 寫 ATDCTL5 ② 當 AFFC=0，向 CCF[n]寫 1 ③ 當 AFFC=1，且 CMPE[n]=1，寫 ATDDRn 30 單片機原理與應用 ATD Registers 10/12 ATD Input Enable Register (ATDDIEN) IEN[15:0] ATD Digital Input Enable on channel x (x= 15, 14, 13, 12, 11, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0) 0=Disable digital input buffer to ANx pin 1=Enable digital input buffer on ANx pin 通用 I/O口 AD口與 ATD模塊的模擬輸入引腳復用 將某個模擬輸入引腳作為通用輸入
環評公示相關推薦
鄂ICP備17016276號-1