【正文】 ing isolation stent along the length of anchor every2000mm.、錨具：錨具（M172,2孔）≥設計值340KN，與鋼絞線2162。 shall be selected in line with the operative norm of GB/T specification of anchor has two types including 3162。、絞線2162。. Length of anchor: its length shall be ～ and the anchorage length shall be 5～ depth that the anchor hacked into the original concrete foundation shall be not less than 1m. 、錨桿入射角度：25度 Injection Degree:25 degree、錨桿直徑：150mm Diameter of anchor:150mm、錨桿：采用鋼絞線162。錨桿施工平面布置詳見附圖（一）（以從上至下為例）所示，然后及時進行后續各工序的施工。 Issuing technical information to staff for study。 Completing the approach and test of raw materials 。The anchor construction shall be performed simultaneously with the slope excavation. After the pletion of supporting construction of upper slope, excavating to the construction location of prestressed anchor, then carrying out the construction of intermediate beam and prestressed anchor and finishing supporting work for slope in order to reduce exposure time of slope. 1) 、準備工作：機具配備質量和數量，人員配置數量和結構等必須與預應力錨桿施工相適應，滿足施工需要；完成原材料進場及試驗檢測；完成施工技術方案、開工報告等技術資料的編寫、上報和審批，技術交底資料的下發學習，原材料送檢、報批手續及資料收集。The main construction contents include: construction preparation,anchor hole positioning and drilling (including consolidation grouting treatment for poor geological section ),anchor processing preparation, hole cleaning and anchoring, grouting for anchorage section (including secondary splitting grouting),concrete pouring for intermediate beam of anchor and anchor inclined supporting, anchor tension, supplementary grouting and anchor seal work, etc. 勞動力組織安排 Plan（1）根據工程的特點及施工組織設計的要求配備勞動定員及設置施工組織機構,主要?jiǎng)趧?dòng)力組織見下表：（1）As per this project characteristic and requirement of construction organization design to arrange workers and set up construction manpower as follows:序號S/N工種Position人數Qty主要工作內容Main Work Content1施工員Engineer5負責測量放線、施工指導及質量控制Measure and setting out,construction guidance and quality control2鉆機司機Drilling rig driver2錨固鉆機操作Operate anchorage drilling rig3砂漿攪拌工Mortar mix worker2攪拌桶操作Mix bucket operation4錨索工Anchor cable worker4負責錨索安裝Anchor cable installation5綜合輔助工Comprehensive assistant worker8負責輔助作業Normal work6電工Electrician2負責施工中涉電作業Electricity operation7鋼筋工Steel bar worker8負責鋼筋制作、綁扎、安裝作業Steel bar fabrication,binding and installation8模板工Form worker13負責模板制作、安裝、加固作業Formwork fabrication, installation and strengthening（2） 錨桿施工組織機構： (2)Construction organization of anchor:現場技術負責人：劉濤；生產負責人：胡延輝；Site technical in charge: Liu Tao Site engineer: Hu Yanhui 專職質量檢查：李慶東；Special quality inspector: Li Qingdong 主要機械設備 Mechanical Equipment預應力錨桿施工進場的主要機械設備如表1所示The main mechanical equipment prepared for prestressed anchor construction are shown in figure1 below.表1 錨桿施工配備機械設備表 Figure1 Mechanical Equipment List for Anchor Construction機械名稱Equipment Name規格型號Specification and Model數量Qty備注Note錨固鉆機Anchorage drilling rig優博林868型Youbolin （Type 868） 2臺2 nos.注漿設備Grouting equipment BLW130型攪漿桶Mortar mixing bucket with type BLW1302套2 sets含不良地質段處理Including the treatment for poor geological section空 壓 機Air pressor12m3柴油12m179。3. Report of Geological Engineering Exploration for proposed Water Treatment Plant and onthespot investigation for the surrounding environment of said construction site.中國現行國家標準、施工技術規范、規程、質量檢驗評定標準及驗收方法、安全檢測標準及技術規程、文明施工要求等。 2. Site Preparation Drawings and Design Description of the Site Preparation of Gampaha,Attanagalla amp。 1. The relevant contents and related technical terms about Site Preparation included in the Bidding Document of Gampaha,Attanagalla amp。斯里蘭卡阿塔納水廠場平工程錨桿分項工程SubEngineering of Anchor for Site LevelingSpecific Method Statement專項施工方案編制：Prepared By:審核：Reviewed By:批準：Approved By:CMEC公司斯里蘭卡阿塔納水廠項目部 Gampaha,Attanagalla amp。 Minuwangoda Integrated Water Supply Scheme 編制時間:2017年09月09日Preparation Date:September 9th , 2017目 錄 Contents第一節、編制依據01 I. Preparation Basis第2節 、施工步驟03 II. Construction Arrangement 一 ）、施工步驟03 1. Construction Arrangement 二）、勞動力組織安排03 2．Manpower Plan 三）、機械設備配置04 Equipment Preparation 四）、主要儀器設備05 4. Main Instrument and Equipment第三節、錨桿主要施工方法06 III Main Construction Method of Anchor 一）、總體方案06 1. Overall Scheme 二）、施工準備08 2. Construction Preparation 三）、錨桿成孔工藝09 3. Boreforming Process of Anchor第四節、施工進度計劃26 IV Construction Progress Schedule附圖一、質量保證機構框架圖32 Attached Figure1 Frame Chart of Quality Assurance Organization 附圖二、安全保證機構框架圖33 Attached Figure2 Frame Chart of Safety Assurance Organization34 / 37第1節 、編制依據 I. Preparation Basis 阿塔納水廠工程招標文件中關于場地平整的相關內容及相關技術條款。 Minuwangoda Integrated Water Supply Scheme. 阿塔納水廠工程場地平整設計施圖、圖說（送審版）。 Minuwangoda Integrated Water Supply Scheme. (Approval Version) 阿塔納水廠工程地質勘探報告及實地考察施工現場周邊環境情況。4. Current national standards in China, technical specifications, procedures, quality i