焊接材料質量管理規定-閱讀頁
2025-06-07 18:17本頁面
【正文】 Welding electrodes, fluxes, wires and flux cored welding wires whose storage life expires may be distributed for use only after they pass reinspection organized by relevant functional departments.Reinspection is generally aimed at checking if any defect likely to affect welding quality occurs to welding materials, and is usually limited to exterior inspection and process performance test. If there is any about service performance of welding materials, necessary inspection items may be included.The specified period is any of the following periods of time as from the date of production:a) Period as remended in quality certificate or specification of welding material supplier。c) The storage life of welding materials with ordinary packing and other welding materials is two years. 受潮、變質的焊接材料對于嚴重受潮、變質的焊接材料，應由質檢和有關職能部門進行必要的檢驗，并作出降級使用或報廢的處理決定之后，方可準許出庫。 Dampened, deteriorated welding materialsFor severely dampened or deteriorated welding materials, quality management and relevant functional departments shall make necessary inspection and decide on concession or scrapping before such materials may be taken out of warehouse. The flow direction of those materials must be strictly controlled.9 使用過程中的管理 一般要求 車間應設置專門的焊接材料管理員，負責焊接材料的焙烘、保管、發放及回收。9. Management during use General requirements The workshop shall have a welding materials management clerk who is responsible for drying, custody, distribution and recovery of welding materials. Responsibility for use and managementProduction supervisor in the workshop assumes overall responsibility for management and use of welding materials。烘干、保溫設施應有可靠的溫度控制、時間控制及顯示裝置。 焊接材料在烘干及保溫時應嚴格按有關技術要求執行。堆高不超過70mm。 不同類型的焊接材料應分別烘干，避免混雜。焊接材料的烘干規范可參照焊接材料說明書的要求確定。 焊接材料管理員對焊接材料的烘干、保溫、發放及回收應作詳細記錄，達到焊接材料使用的可追溯性。 真空包裝焊接材料采用真空包裝，按照焊接材料制造商技術規格書的規定，允許不進行焙烘的焊接材料，可直接使用，但必須在 4 小時內用完，或嚴格按照焊接材料制造商技術規格書的規定發放和使用。 After drying, welding materials shall be kept within a specified temperature range. Welding materials management clerk shall record in detail the drying, heat insulation, distribution and recovery of welding materials to ensure the traceability of welding materials usage. The surface of welding wire must be smooth, tidy and free of oil, rust or filth. Welding materials with vacuum packingIf vacuum packing is adopted, welding materials that are allowed not to be dried according to technical specifications of the manufacturer of welding materials may be directly used but must be used up within 4 hours, or shall be distributed and used in strict accordance with the said technical specifications.If storage life expires or vacuum packing is damaged, welding materials may not be used. 識別標志在使用過程中，應注意保持焊接材料的識別標志，以免發生錯用、混用，造成質量事故?；厥盏暮附硬牧蠎?yīng)滿足下列條件：a) 標記清楚；b) 整潔，無污染。b) Tidy and unpolluted. 回收的焊接材料的烘干焊接前要求必須烘干的焊接材料(堿性低氫型焊條及焊劑)，允許回收后再次烘干，但對烘干溫度超過 350℃的低氫材料，累計的烘干次數不超過 3 次。 Dry of recovery welding materialsWelding materials that must be dried before use (., alkali lowhydrogen welding electrodes and fluxes) may be dried again after recovery. However, lowhydrogen materials that shall be dried above 350℃ may be dried for at most 3 times. Repeated use of welding fluxWelding flux may be used repeatedly, provided that:a) Used welding flux is mixed with new welding flux of the same batch and the mixing ratio of the former is below 50%. For an important product, the mixing ratio of used welding flux is preferably around 30%。c) The granularity of mixed welding flux meets the specified requirement.10. 支持性文件 Supportive Procedures無N/A11. 附錄 Appendix無N/A
環評公示相關推薦
鄂ICP備17016276號-1