焊接材料質量管理規定-免費閱讀
【正文】 b) Tidy and unpolluted. 回收的焊接材料的烘干焊接前要求必須烘干的焊接材料(堿性低氫型焊條及焊劑)，允許回收后再次烘干，但對烘干溫度超過 350℃的低氫材料，累計的烘干次數不超過 3 次。 焊接材料管理員對焊接材料的烘干、保溫、發放及回收應作詳細記錄，達到焊接材料使用的可追溯性。 焊接材料在烘干及保溫時應嚴格按有關技術要求執行。c) The storage life of welding materials with ordinary packing and other welding materials is two years. 受潮、變質的焊接材料對于嚴重受潮、變質的焊接材料，應由質檢和有關職能部門進行必要的檢驗，并作出降級使用或報廢的處理決定之后，方可準許出庫。發現由于保存不當而出現可能影響焊接質量的缺陷時，應及時報告質檢，和相關部門，會同有關職能部門及時處理。h) Effective period (from the date of acceptance to a specified date).After warehousing of welding materials, corresponding storage archives shall be established, including warehousing register, quality certification, classification certificate, acceptance report, and inspection and distribution records.7 庫存保管 存放條件 焊接材料的儲存庫應保持適宜的溫度及濕度。焊接材料入庫后即應建立相應的庫存檔案，如入庫登記、質量證明書、船級社證書、驗收檢驗報告、檢查及發放記錄等。 成分及性能試驗如需要，應按技術要求進行焊接材料復驗，根據有關標準或供貨協議的要求，進行相應的試驗。在可能的條件下，盡量配套采購。所有標準都會被修訂，使用本標準的各方應探討使用下列標準最新版本的可能性。本標準適用于焊接生產中，上述這些焊接材料的質量管理。 對業主規定有特殊要求的項目，要根據業主的規定要求修訂具體項目的管理規定，并監督執行。 包裝檢驗檢驗焊接材料的包裝是否符合有關標準要求，是否完好，有無破損、受潮現象。 Exterior inspectionCheck and make sure the exterior of welding materials is uncontaminated, free of any defect that occurs during storage or transportation and is likely to affect welding quality, and that their identification marks are clear and fast and consistent with actual conditions of the products. Composition and performance testIf necessary, welding inspection shall undergo reinspection in accordance with technical requirements or corresponding tests as required in relevant standards or supply agreement. Approval of inspection resultsThe methods and rules for inspection of welding materials shall be generally determined in accordance with the requirements of relevant standards and classification society rules. If necessary, such methods and rules may be determined through negotiation by the buyer and the seller.After acceptance inspection of welding materials, an inspection report shall be issued, subject to approval by relevant functional departments. Inspection markEach package of accepted welding materials shall be properly marked.6 入庫存放焊接材料的庫內可根據需要，劃分為“待檢”、“合格”及“不合格”等區域，各區域要有明顯的標記。e) Quantity (or weight)。品種、型號及牌號、批號、規格、入庫時間不同的焊接材料，應分類、分批存放，并有明確的區別標志，以免混雜。規定期限自生產日期始可按下述方法確定：a) 材料供應商的焊接材料質量證明書或說明書推薦的期限；b) 包裝密封良好的焊接材料為三年；c) 一般包裝的焊接材料，及其他焊接材料為二年。Welding technicians and workshop inspectors shall conduct necessary inspection and supervision over the management and use of welding materials to ensure correct use of welding materials and prevent quality accident due to inappropriate management of welding materials. 烘干、保溫及清理 烘干及清理焊接材料的場所應具備合適的烘干、保溫設施，及清理手段。 焊接材料制造廠對有烘干要求的焊接材料，應提供明確的烘干條件。 焊接材料的回收焊接工作結束后，剩余的焊接材料應回收。b) Before mixing, slag, impurities and dust is properly removed from used welding flux。如果超過保存期，或發現真空包裝破損，禁止使用。烘干焊條時應注意防止焊條因驟冷驟熱而導致藥皮開裂或脫落。 使用管理職責車間的生產主管人員對焊接材料的管理及使用全面負責；焊接技術人員及車間檢查員應對焊接材料的管理及使用進行必要的檢查監督，確保焊接材料的正確使用，防止由于焊接材料管理不善而發生質量事故。8. Distribution To ensure the use of welding materials within effective period and avoid bad consequence of expiration of storage life, the distribution of welding materials shall follow the “FIFO (first in, first out)” principle. The quantity of welding materials taken out of warehouse shall be controlled in strict accordance with product consumption data, and warehousing materials may be sent out of warehouse only against the corresponding material requisition and with the approval by storekeeper. 庫存超期的焊接材料庫存期超過規定期限的焊條、焊劑、焊絲及藥芯焊絲，需經有關職能部門復驗合格后方可發放使用。 焊接材料應按有關的技術要求和安全規程妥善保管。c) Specificatio
環評公示相關推薦
鄂ICP備17016276號-1