模具外貿葵花寶典-在線瀏覽
2024-08-17 14:59本頁面
【正文】 an oil cylinder to assure that the process is in proper order.)54. 這個面有裝配，加料的話裝配時會頂住，如圖所示(We cannot add material to this surface because it will intervene between the two parts when it is assembled. Please see the sketch attached. )55. 可降低斜銷面，增加成品些許肉厚來做變化(To descend the surface of lifter in order to thicken the part.)56. 一半做斜銷，一半做自然 (One half side will have the lifter and the other half will be solid/nature.)57. 此處兩個柱子重疊，有倒勾，不能做自然，要做SLIDE(These two bosses are overlapping with undercut therefore it can not be made as solid. Wesuggest making it with a slide block.)58. 此處強迫頂出 (This area needs force ejection.)59. 公模兩段開模，這個地方先退 (Here will be a double ejection for forward and receding.)60. 此處做鑲件會有夾線，能否接受Please confirm whether it is acceptable that there will be a split line here.) 資料 個人短信 只看該作者 61. 此面公母模1度靠破，會有段差，可否接受(Please confirm whether it is ok to have mismatch to the area where there is 1 degree of shut off in Core / Cavity side.)62. 這個尺寸能否加大 (Please confirm whether we can enlarge this dimension.)63. 此處加一個凹槽，膠片的彈出效果會更好一些，試模後看裝配的效果再做修正(It will affect the elastic of the film better if we add a recess. See how it will affect the assembly parts, and then make your decision.)64. 此處有倒勾，建議將剖面線所示部位CUT即可避免此處的倒勾(There is an undercut here, we suggest cutting out the indicated part as it highlighted to avoid an undercut.)65. 成型後SUB GATE要修平 (The gate (sub gate) needs to be trimmed evenly after being moulded.)66. 此處倒勾先垂直頂出，之後再手動取出(This area of the undercut needs to be ejected vertically, then taken out manually.)67. 這兩個面都有滑塊，GATE改在此處改不到(The gate is not suitable in this area becuase there are two sliding blocks sealing off this area.)68. 此處加做一個旋轉GATE，射出時方便調整成品的品質(We would suggest placing a runner shutoff insert to adjust the volume of part filling.)69. 此倒勾在滑塊上強迫脫模，(This undercut will be force ejected out, Please confirm whether it can be reduced to mm.)70. 此柱子無法脫模，請確認是否是在轉圖時錯位，能否提供客戶的原始圖檔 data. )(This boss is not releasable. Please check the file again and if possible, pleas resend us the original draft 資料 個人短信 只看該作者 謝謝LZ的分享,進來了解了解 資料 個人短信 只看該作者 71. 此柱子是實心的，會縮水 (This boss will shrink because it is a solid boss.)72. 這個面是否要咬花，咬花番號是什麼，最小的拔模角要多大(Please confirm whether this surface needs to be textured or not. Please advise texture specs. Also,what39。Insert/PL should have adequate venting,PL should have around slot for venting.,5mm,攻m20牙。 H（保證吊模時的平衡）。Sprue type:Trial/Delivery：NPT規格。報告 wylwyl VIP會員 來自 江蘇狀態 離線 10使用道具發表于 200777 10:08 個人空間 加為好友 Imperial Unit全部使用英文和英制單位Are part dimensions to print plus shrink?請檢查內模尺寸有否乘縮水?All wires protected from sharp corners？凡有電線通過的角位要改為R角，是否完成？All replaceable ponents must be standard 。All moving ponents should use hardened steel : all slides should be installed with hardend or lubricated alloy wear plates and gibs, and with positive slide retainer.所有移動的零件應使用硬鋼料，行位必須用硬墊板和硬線條，而且必須有限位及定位鎖。報告 wylwyl VIP會員 來自 江蘇狀態 離線 11使用道具發表于 200777 10:09 個人空間 加為好友custom ,頂針和自制的零件.BeCu for lifters if w/o water circuits。Corresponding ponents mirrored at coreamp。Conductmoldflow amp。Component and/or 3D mould design
環評公示相關推薦
鄂ICP備17016276號-1