freepeople性欧美熟妇, 色戒完整版无删减158分钟hd, 无码精品国产vα在线观看DVD, 丰满少妇伦精品无码专区在线观看,艾栗栗与纹身男宾馆3p50分钟,国产AV片在线观看,黑人与美女高潮,18岁女RAPPERDISSSUBS,国产手机在机看影片

正文內容

wh212減速機殼體加工工藝及夾具設計【最新】-展示頁

2024-11-20 07:47本頁面
  

【正文】 0mm) 專用銑床 6 粗銑、半精銑 以結合面及軸承孔定位,裝夾工件銑底面。 (工藝尺寸 ) 專用銑床 7 鉆 鉆低面 4φ 19mm 孔 ,其中兩個鉸至φ+(工藝用 )刮平φ 36 專用鉆床 8 鉆 以底面及銷釘定位,鉆 4φ 11 刮背面φ25,鉆 4φ 13 刮背面φ 28 專用鉆床 9 鉆 以兩個工藝孔及底面定位,加緊工件,鉆、鉸φ 25mm 測油孔,锪φ 56mm 深 2mm.鉆、攻 3M6 深 10mm,鉆、攻 底孔,刮平φ 25mm 專用鉆床 10 磨 以一面兩孔定位,裝夾工件。 專用磨床 11 鉗工 箱體底部用煤油做參漏試驗 12 檢查 檢查各部尺寸及精度 減速器 WH212 箱體的工藝過程 攀枝花學院機電工程學院畢業設計專用紙 6 工序號 工序名稱 工 序 內 容 工藝裝備 1 鉗 將箱蓋,箱體對準合箱,用 4M10,4M12的螺栓,螺母緊固 2 鉆 鉸 2 ? 6mm, 1: 50 錐,裝入錐銷 專用鉆床 3 鉗 將箱蓋,箱體做標記編號 4 粗銑、半精銑 以底面與兩孔定位,按底面一邊找正。夾緊工件,兼顧一面的加工尺寸,銑另一端面,保證尺寸 285 ? 專用銑床 6 粗鏜 以底面定位,以加工過的端面找正,裝夾工件,粗鏜 2? 110 ?? 軸承孔,留加工余量 ~。保證兩軸中心線的垂直度公差 保證結合面與軸承孔的位置度公差為 專用鏜床 8 精鏜 以底面定位,以加工過的端面找正,裝夾工件,按結合面精確對刀(保證結合面與軸承孔的位置度公差為 )精鏜2? 110 ?? mm 專用鏜床 9 鉆 用底面與兩銷釘定位用鉆摸板鉆、攻蝸桿軸承孔端面螺孔 專用鉆床 攀枝花學院機電工程學院畢業設計專用紙 7 10 鉆 鉆、攻蝸輪軸承孔端面螺孔 專用鉆床 11 鉆 用帶有錐度的直徑為φ 120~φ 130mm 的90 度的鉆锪鉆锪軸承孔內邊緣倒角41x45 度 專用鉆床 12 鉗 拆箱、清理飛邊、毛刺 13 鉗 合箱、裝錐銷緊固 14 檢驗 檢查個部尺寸及精度 15 入庫 入庫 當加工兩個面時 ?tm 鉆 ? 13 孔 L=30mm mmmm ll 1321 ?? 960?nw r/min 1330421?????????flnlltwm 當加工兩組孔時 t= ? ???tm 鉆孔放置時,在專用鉆床上鉆φ 19 mm 孔的鉆前力和扭矩力均由重力與外力來承擔,這時工件的夾緊可以有兩種方案: ( 1) 在箱體的底面上,采用壓板壓緊,夾緊力與切削力處于平行狀態。 ( 2) 在箱體的底面上采用螺紋夾緊裝置,加緊力與切削力平行,這種結構簡單。 三、切削力及夾緊力的計算 刀具:麻花鉆, dw=19mm, 則 F= Fz (《切削手冊》 ) 查表得: d0=19mm,ae=195, af =, ap =, δ Fz = 所以: F=( 192 20 ) 247。 ( 2) 這種布置型式可用同一尺寸的后鏜套而進行多工步加工。 ( 4) 用于立鏜時,無切削落入鏜套之慮。但這樣將導致整個鏜套部分的結構龐大。 三、夾緊力大小的確定原則 夾緊力大小對于確定夾緊裝置的結構尺寸,保證夾緊可靠性等有很大影響。夾緊力過小則工件夾不緊,在加工過程中容易發生工件位移,從而破壞工件定位,也影響加工精度,甚至造成安全事故。 計算夾緊力時,通常將夾具和工件看成一個剛性系統,然后根據工件受切削力、夾緊力(大工件還應考慮重力,運動的工件還需考慮慣性)后處于靜力平衡 攀枝花學院機電工程學院畢業設計專用紙 9 條件,求出理論夾緊力,為了安全起見再乘以安全系數 K。如圖 21 所示切削方向進行靜力平衡,求出理論夾緊力,再乘以安全系數即為實際夾緊力,圖中 W 為夾緊力, N N1`…為鏜孔各方向鏜削力,可按切削原理中求切削力。既KNKNW ?? 圖2 1 (二)在分析受力時,往往可以列出不同的工件靜平衡方程式。如圖所示垂直方向平衡式為 W=。 攀枝花學院機電工程學院畢業設計專用紙 10 圖 24 定位裝置為一面兩銷,第一個定位銷的最大工作高度為 mmdd dl XH m inm a x???????? 第二個定位銷的最大高度為 ? ?? ?mmdLdL dlL XH m inm a x???? ????????? 式中 d—— 定位銷直徑; Xmin —— 定位 副最小間隙。 結論: 通過本次的畢業設計,使我能夠?qū)镜闹R做進一步的了解與學習,對資料的查詢與合理的應用做了更深入的了解,本次進行工件的工藝路線分析、工藝卡的制定、工 藝過程的分析、鏜鉆夾具的設計與分析,對我們在大學期間所學的課程進行了實際的應用與綜合的學習。 [2]周增文 張亮蜂等編著,《機械加工工藝基礎》,中南大學出版社。 [4]李喜橋編 ,《加工工藝學》,北京航空航天大學出版社。 [6]陳宏均主編,《實用機械加工工藝手冊》,機械工業出版社。 攀枝花學院機電工程學院畢業設計專用紙 11 [8]王生力主編,《重型機械制造工藝學》,冶金工業出版社 1986 年。 [10]李慶壽主編,《機床夾具設計》,機械工業出版社 1984。 [12]貴州工學院機制工藝研究室編,《機床夾具結構圖》,機械工業出版社 1983。 [14]潘曉弘,《機械制造工程》,浙 江大學出版社 2020 年。 [16]于駿一主編,《典型零件制造工藝》,機械工業出版社 1989 年。 [18]樂兌謙主編 .《金屬切削刀具》機械工業出版社, 1985。陳老師和張書記不僅以其淵博的學識、創造性的思維方式、嚴謹?shù)闹螌W(xué)風范、高度的責任感使作者在學術上受益匪淺、而且言傳身教,以其高尚的人格和坦蕩寬廣的胸懷教導了我做人的道理。 在設計工作中,得到了機電工程學院有關領導和老師的幫助與支持,在此表示衷心的感謝。 吳紫東 2020 年 6 月 10 日 于攀枝花學院機電工程學院 Personal puter Systems When you mention the word ―technology‖, most people think about puters. Virtually every facet of our lives has some puterized ponent. The appliances in our homes have microprocessors built into them, as do our televisions. Even our cars have a puter. But the puter that everyone thinks of first is typical the personal puter ,or PC. A PC is a generalpurpose tool built around a microprocessor. It has lots of different partsmemory, a hard disk ,a modem ,etc.—that work together. ―General purpose‖ means that you can do many different things with a PC. You can use it to type 攀枝花學院機電工程學院畢業設計專用紙 13 documents, send , browse the Wed and play games. On the Inside Let us take a lood at athe main ponents of a typical desktop puter. Central processing unit(CPU)—The microprocessor ―brain‖ of the puter system is called central processing unit. Everything that a puter does is overseen by the CPU. Memory—This is very fast storage used to hold data. It has to be fast because it connects directly to the microprocessor. There are sever specific types of memory in a puter: Randomaccess memory(RAM)—Used to temporarily store information that the puter is currently worling with Readonly memory(ROM)—A permanent type of memory storage used by the puter for important data that does not change Basic input/output system(BIOS)—A type of ROM that is used by the puter to establish basic munication when the puter is first turned on. Caching—The storing of frequently used data in extremely fast RAM that connects directly to the CPU Virtual memory—Space on a hard disk used to temporarily store data and swap it in and out of RAM as needed Motherboard—This is the main circuit board that all of the other internal ponents connect to. The CPU and memory are usually on the motherboard. Other system may be found directly on the motherboard or connected to it through a secondary connection. For example, a sound card can be built into the motherboard or connected though PCI. Power supply—An electrical transformer regulates used by the puter . Hard disk—This is largecapacity permanent storing used to hold information such as programs and documents. Operating system—This is the basic software that allows the user to interface with the puter. Integrated Drive Electronics(IDE)Controller—This is the primary interface for the hard drive, CDROM and floppy disk drive Peripheral Component Interconnect(PCI) Bus—The mostr mon way to connect additional ponents to the puter, PCI uses a series of slots on the motherboard that PCI cards plug into . SCSI—The small puter system interface is
點擊復制文檔內容
環評公示相關推薦
文庫吧 www.dybbs8.com
備案圖鄂ICP備17016276號-1