【正文】 Pair and put it on the conveyer belt to process the next procedure. Applied Tooling: 後幫機 Heel lasting machine PRESS HEEL LASTING 鳥嘴鉗 Pincers 壓後幫 對比後跟高度 ROUGHING 1,在磨景機上裝上正確的砂帶 ﹐ 一般用 4060的 ,將余皮折縐磨平。 Make the counter dry not more than 15 minutes. . The operator should wear the safe things of glove respirator. Applied Tooling: 鐵網(wǎng) Iron meshwork 手套 Glove 鑷子 forceps 鐵架 Iron shelf 1,從裝鞋面的車架上取下鞋面 ,貼上流水標以便配雙作業(yè) ,剪斷連線 ,放鞋面入流水帶上 . Take the upper from the shelf and attach pair number sticker, then snip the thread that make one pair of upper together, at last put upper on conveyer belt. 2,剪線時不要剪到鞋面 . Don’ t break the upper when snip thread. . Note: Need make the upper pair. PREPARE UPPER Applied Tooling: 剪刀 scissor ,對折好再夾在夾子上 ,刷膠時將泡棉在膠水裡浸一下 . Prepare a little piece of foam or cloth and fold then nip it with clamp. Soak a moment before cementing. ,將楦頭底面周圍 10MM寬刷白膠 Take the last from the shelf , then cement around last bottom 10mm width with latex. 3,刷膠時左手握楦頭 ,右手拿夾子 .刷膠要均勻到位 . During cementing ,the left hand hold the last the right hand hold clamp. Make sure to cement evenly and pletely. . The operator should wear the safe things of respirators. CEMENT LAST BOTTOM WITH LATEX Applied Tooling: 夾子 Clamp 膠壺 Glue pot CEMENT THE INSOLE BOARD ,壓力 30KG,時間 5” . Mold the insole board with pressure 30kg time 5” . 2,刷膠前將中底板排放整齊 ,左手壓住中底板 ,右手拿刷子 . Before cementing ,the left hand hold the last the right hand hold clamp. 15MM寬刷白膠 ,刷膠要均勻到位 . Take the insole board from the shelf , then cement around the top of insole board 15mm width with latex. Make sure to cement evenly and pletely. . The operator should wear the safe things of respirators. Applied Tooling: 夾子 Clamp 膠壺 Glue pot CEMENT HEEL UPPER ,膠水要均勻 ,到位 .不可積膠 . Cement the both sides of collar lining and heel upper with 766N yellow glue. Make sure to cement evenly pletely but not amass into a pile. 2,刷好膠的鞋面 ﹐ 按規(guī)定在流水線上排放整齊 , 保持順暢的流程 ,流進烘箱。 Clip the counter with forceps and then put it into 513 primer . Don’t soak counter too long to avoid the counter from soften. 3﹐ 康特浸好后需放在鐵綱滴干。 鞋面與大底成型 ASSEMBLE UPPERO/S 依照鞋子結構的不同 , 通常分車中底與結幫兩種成型流程 : According to the different shoe construction, there are two kinds of assembly procedure ,strobel lasting. 結幫流程又分為一次流程及兩次流程或多次流程 . For the lasting construction, there are 3kinds of procedure ,one time lasting two times lasting or more than two time lasting. 這裡僅以一次結幫流程為例 ,了解成型的過程 : Here only show the one time lasting procedure for example to know the assembly procedure: 1. 浸 康 特 SOAK TR COUNTER 1,浸康特時注意康特角不要浸膠。 Pay more attention to the bottom of TR counter can’ t be soaked. 2﹐ 用鑷子夾住康特放入 513藥水中 ,只要除康特腳外其他部分有碰到膠水 ,就馬上取出來 .浸膠不宜過久 ﹐ 過久會使康特軟化。 Put the counter on the iron shelf after soaking. 4﹐ 康特擺放鐵架上涼干時不宜過久 ,不要超過 15分鐘。 Put the upper on the conveyer belt in order to keep the procedure smooth through oven after cement. 70度 ,時間 1分鐘 . Adjust the temperature 70 time 1min . ,軟化鞋面 . Let glue dry soften the upper through the oven. Applied Tooling: 刷子 Brush 膠壺 Glue pot 鞋面後跟 /滾裡刷膠 過烘箱 ATTACHE HEEL COUNTER ﹐ 右手拉開內里 .