【正文】 Material should be forming to required specification and class in design drawings. Dimentional / tagging errors shall be processed in accordance with procedure ―Control of Nonconforming Product‖, ref. CDB0000QAC PCDSC20000000700. （ 2） 當要求切割直管時，根據管道材質及焊接工藝要求實施火焰切割或機械切割（熱處理管道），切割后標識應進行移植。 All pipe prefabrication ponents shall be tagged with the numbers of the equipment and pipe they are attached to. ? 有限的管道預置將在施工現場由承包商在臨時制作設施中進行，預制管道的制作場地和臨時堆放區域詳見 下圖 。 Anticorrosion and coating shall be done before pipe prefabrication, the coating method should be in accordance with Construction Method Statement for Sand Blasting and Paint Spraying CDB0000TECPLNSC2 0000001000. . 管段 預制 Prefabrication ? 管道預制加工采用機械化作業和傳統手工焊接作業的方式進行。 After acceptance, acceptance inspection record should be done for equipment and piping ponent. 所有設備、材料、管道組成件 等進場物資首先進行外觀質量、規格參數檢查、做好標識，并對其備件及相關資料登記。 The appearance of steel pipe should not have crack, bump, stratification, overburn, lap, inclusion and other defects, sampling ratio is 10% as per system as well as not less than five pieces, if unqualified, all of them should be fully checked. 鋼管表面有銹蝕、麻點或劃痕等缺陷時，其深度不應大于該鋼材厚度負允許偏差值 1/2。 Construction material preparation: According to physical work quantity and construction plan requirements of this project, it will propose material supply plan and material withdrawal plan and get the relevant consumables and processed members done. Materials can not be used unless been reported, inspected and qualified. ? 施工關系協調：施工前會同 CDB 和監理單位以及有關協作單位對本工程的施工范圍、施工作業區域、施工作業界限以及其它特殊事項進行確定，從而確保工程的順利開展和交接。 Preparation of construction machine and personnel: all machinery equipments shall be plete and intact, it only can be used after passing CDB inspection and being reported。 站內露空管道系統安裝方案 Method Statement for Installation of Exposed Pipeline in Well Pad and Gathering Station 5 CONTRACTOR shall provide all Supervisors, the required HSE training to all personnel including SUBCONTRACTOR personnel. All personnel shall have an HSE Passport prior to mobilization to site. ? 特殊工種作業人員必須取得相應工作的資質證件，且報審合格。 Workers will contact following personnel in accordance with corresponding procedures if any unexpected medical, security incidents or accidents happen. The sequence of contact shall be based on the best interest of handling the incidents or the injured. 聯系單位 (所在地址 ) Contact (Location) 聯系電話 Tel Number CDB 南壩安全控制中心 Nanba safety control center 13911678263。 Firstaid kit will be needed on construction site. The articles in firstaid kit will be conforming to requirements of Chuandongbei Project. ? 在施工中若發生緊急事件，按照《事故管理程序》 CDB0000HESPCDSC20000001400 進行上報。禁止在同一施工區域同時進行兩項作業。 Ensure all relevant activities and method statements be approved before execution, otherwise they will be stopped at once. ? 承包商應負責此方案中所描述活動的執行。 No smoking in operation area, except the designated smoking area which will be set on site. ? 廢物的管理，包括防腐涂料、液體清潔劑的使用與回收，需設置垃圾回收箱，按照 CDB廢物管理要求處理到指定地點，確保環境不受污染。 hard barricade maybe required when it is necessary to avoid accessing into it without permit. ? 作業現場必須按照每 ―50名作業人員： 1名安全員的比例進行配備，以保證 現場人員、物資的安全。 Forman will be assign for work at height. Workers must wear full body harness and keep the principle of hanghigh use low being followed. Work zone and body harness hanging points should be checked and confirmed before operation. ? 臨時用電安全措施，配電箱布置。禁止在下雨露天進行焊接作業。 When perform stainless steel, make proper respiration protection against chromium VI (if required). ? 所有人員都應參加了適應的安全培訓并佩戴 PPE,如作為最低要求的安全帽，鋼頭鞋，安全眼鏡和工作服以及根據具體情況需要穿戴的安全手套、高亮背心以及面罩等。 ENVIRONMENT . 風險評估 Risk Assessment 此方案風險 分析詳見附件 1。各種材質特性及相關切割、焊 接、熱處理要求詳見 PQR 說明。 METHOD STATEMENTS ......................................................... 1 . 相關程序文件和方案 RELATED PROCEDURES AND METHOD STATEMENTS ........................................................ 1 . 相關設計文件及規 范 RELATED DESIGN DOCUMENTS AND SPECIFICATIONS ...................................................... 2 3. 健康、安全與環境 HEALTH, SAFETY amp。 ENVIRONMENT ................................................................................ 2 . 風險評估 RISK ASSESSMENT................................................................................................................................... 2 . HSE 要求 HSE REQUIREMENTS.............................................................................................................................. 3 . 應急救援 EMERGENCY RESPONSE ........................................................................................................................... 4 4. 培訓和人員資質 TRAINING AND COMPETENCY OF PERSONNEL .............................................................. 4 5. 工藝 PROCESS............................................................................................................................................................... 5 . 施工準備 PREPARATION FOR CONSTRUCTION .......................................................................................................... 5 . 流程 PROCESS FLOW ................................................................................................................................................ 5 . 材料檢查及驗收 ACCEPTANCE INSPECTION OF CHECK ........................................................................................ 6 . 管段預制 PREFABRICATION...................................................................................................................................... 7 . 焊接 WELDING ........................................................................................................................................................ 10 . 不銹鋼 STAINLESS STEEL ....................................................................................................................................... 12 . 無損檢測 NONDESTRUCTIVE TEST (NDT) ...................................