【文章內容簡介】 IE vector table: // Disable CPU interruptsDINT。// Initialize the PIE control registers to their default state.// The default state is all PIE interrupts disabled and flags // are cleared.// This function is found in the ()。// Disable CPU interrupts and clear all CPU interrupt flags:IER = 0x0000。IFR = 0x0000。// Initialize the PIE vector table with pointers to the shell Interrupt // Service Routines(ISR).// This will populate the entire table, even if the interrupt // is not used in this is useful for debug purposes.// The shell ISR routines are found in .// This function is found in ()。// Step all the Device Peripherals: // This function is found in // InitPeripherals()。// Not required for this exampleInitXintf()。// For this example, init the Xintf // Step specific code, enable interrupts:init_eva()。//init_evb()。while(1){for(i=0。i{Reg06=0。 = i。delay_loop()。}} } void delay_loop(){shorti,j。for(i = 0。i 1000。i++){for(j = 0。j 10。j++)。} } void init_eva(){ // EVA Configure T1PWM, T2PWM, PWM1PWM6 // Initalize the timers// Initalize EVA Timer1 = 0xFFFF。// Timer1 period = 0x3C00。// Timer1 pare = 0x0000。// Timer1 counter// TMODE = continuous up/down// Timer enable// Timer pare enable = 0x1042。// Initalize EVA Timer2 = 0x0FFF。// Timer2 period = 0x03C0。// Timer2 pare = 0x0000。// Timer2 counter// TMODE = continuous up/down// Timer enable// Timer pare enable = 0x1042。// Setup T1PWM and T2PWM// Drive T1/T2 PWM by pare logic = 1。// Polarity of GP Timer 1 Compare = Active low = 1。// Polarity of GP Timer 2 Compare = Active high = 2。// Enable pare for PWM1PWM6// = 0x0C00。// = 0x3C00。 = 0xFC00。// Compare action that takes place// on a cmpare event// output pin 1 CMPR1active low// output pin 3 CMPR2active low// output pin 5 CMPR3active low = 0x0666。 = 0x0000。// Disable deadband = 0xA600。}void init_evb(){ // EVB Configure T3PWM, T4PWM and PWM7PWM12 // Step 1active high// output pin 2 CMPR4active high// output pin 4 CMPR5active high// output pin 6 CMPR6x000 0000 0011 0000EDIS。// Step PIE vector table:// The PIE vector table is initialized with pointers to shell Interrupt// Service Routines(ISR).The shell routines are found in .// Insert user specific ISR code in the appropriate shell ISR routine in// the file.// Disable and clear all CPU interrupts:DINT。IER = 0x0000。IFR = 0x0000。// Initialize Pie Control Registers To Default State:// This function is found in the file.// InitPieCtrl()。PIE is not used for this example// Initialize the PIE Vector Table To a Known State:// This function is found in .// This function populates the PIE vector table with pointers// to the shell ISR functions found in ()。// Enable CPU and PIE interrupts// This example function is found in the ()。// Step all the Device Peripherals to a known state:// This function is found in // InitPeripherals()。skip this for SCI tests// Step specific functions, Reassign vectors(optional), Enable Interrupts:LoopCount = 0。ErrorCount = 0。scia_fifo_init()。// Initialize the SCI FIFOscia_loopback_init()。// Initalize SCI for digital loop back// Note: Autobaud lock is not required for this example// Send a character starting with 0SendChar = 0。// Step Characters forever starting with 0x00 and going through // sending each, check the recieve buffer for the correct value for(。){ scia_xmit(SendChar)。while(!=1){ } // wait for XRDY =1 for empty state// Check received characterReceivedChar = 。if(ReceivedChar!= SendChar)error(1)。// Move to the next character and repeat the testSendChar++。// Limit the character to 8bitsSendChar amp。= 0x00FF。LoopCount++。if(LoopCount==256){LoopCount=0。 =0。// Disable loop back =0x0023。// Relinquish SCI from Reset while((ReceivedChar = )!=0x0d)。scia_loopback_init()。// Initalize SCI for digital loop back}} }// Step all local Interrupt Service Routines(ISRs)and functions here: void error(int ErrorFlag){ErrorCount++。//asm(“ESTOP0”)。// Unment to stop the test here //for(。)。} // Test 1,SCIA DLB, 8bit word, baud rate 0x000F, default, 1 STOP bit, no parity void scia_loopback_init(){// Note: Clocks were turned on to the SCIA peripheral// in the InitSysCtrl()function =0x0007。// 1 stop bit, No loopback// No parity,8 char bits，// async mode, idleline protocol =0x0003。// enable TX, RX, internal SCICLK，// Disable RX ERR, SLEEP, TXWAKE =0x0003。 =1。 =1。=0x0001。=0x00e7。} // Transmit a character from the SCI39。 void scia_xmit(int a){=a。}// Initalize the SCI FIFO void scia_fifo_init() =1。// Enable loop back =0x0023。// Relinquish SCI from Reset{=0xE040。=0x204f。=0x0。}//============================= // No more.//=============================第三篇：DSP實驗報告實驗0 實驗設備安裝才CCS調試環境 實驗?zāi)康模喊凑諏?shí)驗講義操作步驟，打開CCS軟件，熟悉軟件工作環境，了解整個工作環境內容，有助于提高以后實驗的操作性和正確性。實驗步驟：以演示實驗一為例：1． 使用配送的并口電纜線連接好計算機并口與實驗箱并口，打開實驗箱電源；2．啟動CCS，點擊主菜單“ProjectOpen”在目錄“C5000QuickStartsinewave”，然后點擊主菜單“ProjectBuild”編譯，然后點擊主菜單“FileLoad Program”；3． ，在注釋行“set breakpoint in CCS！!”語句的NOP處單擊右鍵彈出菜單，選擇“Toggle breakpoint”加入紅色的斷點，如下圖所示；4． 點擊主菜單“ViewGraphTime/Frequency…”，屏幕會出現圖形窗口設置對話框5． 雙擊Start Address，將其改為y0；雙擊Acquisition Buffer Size，將其改為1；DSP Data Type設置成16bit signed integer，如下圖所示；6． 點擊主菜單“WindowsTile Horizontally”，排列好窗口，便于觀察7． 點擊主菜單“DebugAnimate”或按F12鍵動畫運行程序，即可觀察到實驗結果：心得體會：通過對演示實驗的練習，讓自己更進一步對CCS軟件的運行環境、編譯過程、裝載過程、屬性設置、動畫演示、實驗結果的觀察有一個醒目的了解和熟悉的操作方法。熟悉了DSP實驗箱基本模塊。讓我對DSP課程產生了濃厚的學習興趣，課程學習和實驗操作結合為一體的學習體系，使我更好的領悟到DSP課程的實用性和趣味性。實驗二 基本算數運算 實驗?zāi)康暮鸵蠹?、減、乘、除是數字信號處理中最基本的算術運算。DSP 中提供了大量的指令來實現這些功能。本實驗學習使用定點DSP 實現16 位定點加、減、乘、除運算的基本方法和編程技巧。 實驗原理 定點 DSP 中的數據表示方法C54X 是16 位的定點DSP。一個16 位的二進制數既可以表示一個整數，也可以表示一個小數。當它表示一個整數時，其最低位（D0）表示20，D1 位表示21，次高位（D14）表示214。實現 16 位定點加法C54X 中提供了多條用于加法的指令，如ADD，ADDC，ADDM 和ADDS。其中ADDS 用于無符號數的加法運算，ADDC 用于帶進位的加法運算（如32 位擴展精度加法），而ADDM 專用于立即數的加法。實現 16 位定點減法C54X 中提供了多條用于減法的指令