【文章內容簡介】 ty issue, it must be promised by our customer first, then can be made the UAI decision.UAI: , 則可做讓步接受, MRB評判結果記錄在MRR單上, 且至少有QA經理，采購和工程部或其部門經理的指定代表簽署，必要時需生產經理簽署。. QA和ME應監控生產中使用效果.注意: 如果此不良有可能影響到成品的質量問題, 則必須得到客戶的許可才能做出讓步接受的決定. Sort/Rework: If the material is urgent for produce, and for MRB evaluation the defect will be full eliminated by easy sort/rework, the SORT/Rework decision will be made based on the negotiation with the supplier, the MRB result should be recorded on the MRR sheet, it must be approved by the managers or whose representative of QA, ME, PRD, PUR. The sorting/rework responsibility by either a specified department or supplier. Namely, sort internally or sort externally.選用/返工: 如果該物料為生產線急需, 且經MRB小組判定經簡單加工/挑選即可完全消除不良缺陷, 根據與供貨商談判的結果可進行選用/返工處理, MRB評審結果記錄于MRB單上, 至少有QA經理, ME經理, 生產部經理, 采購或其指定的代表簽署, 指定由供貨商或相關部門篩選,即分為內部篩選和外部篩選. Scrap: If the defect can’t be retrieved or the supplier authorizes to scrap the rejected part, the decision should be recorded on the MRB form. The authorization of scrap must be approved by the manager QA, PUD at least, if necessary the scrap should be submitted to Plant Manager for approval.報廢: 不可修復的缺陷或得到供貨商授權報廢的不良品，其決議內容都應記錄于MRB單上. 至少由QA經理, 采購經理簽署, 如有必要, 報廢申請需提交廠長作批準. The disposition to the material purged out should be confirmed by QA manager.對被清除物料的處置, 物料評審會議結果須由QA經理確認. If the MRB meeting result is sorting/reworking, an ining sorting/reworking report should Be filled out (Form No:) when it is necessary. When the sort/rework over, IQC must reinspect the good part upon normal sampling plan. If it’s a supplier problem, Purchaser should raise the charge request of sort/rework cost to the supplier and follow up.如果MRB結果為選用/返工, 必要時需填寫物料選用/返工報告(Form No:), 選用/返工完成后, 需經IQC重新檢驗. 通常情況下, 如果是供貨商的原因, 選用/返工費用由物料供貨商支付. 采購負責跟進對供貨商索賠結果的落實情況. If a certain part should be restricted using as per the MRB decision, this part should be identified with a MRB label and note “UAI” marking.如果MRB會議決定需限制使用的物料, 可讓步接受后再加貼MRB標簽, 并注明UAI. IQC inspector will stamp or label the material with corresponding remarks, such as RTV, UAI, Sort, Rework or Scrap as per MRB decision. The receiving person should transfer the material to the part store accordingly.IQC檢驗員根據MRB結果對物料進行相應標