【文章內容簡介】 正確后按PRO鍵進調整范圍之百分比。（14） 再按PRO鍵進鎖定與修改熒幕。STORE MODIFY XXX XXX鎖定（存） 修改（15） 按 C鍵回到設定熒幕，完全設定。ARC MACHINES,INC COPYRIGHT 199413 JUN 1997 OD WALL TYPE MAT QTY001 PIPE SS 0000PREPURGEPOST UPSLOPEDOWN ROT—DLY20 20 CW LVL PULSE ROT PRI—RPM—BCK1 ON CONT TIME PRIAMPBCK PRIPULSEBCK1 65 20 LVL PULSE ROT PRI—RPM—BCK2 ON CONT TIME PRIAMPBCK PRIPULSEBCK2 60 20 LVL PULSE ROT PRI—RPM—BCK3 ON CONT TIME PRIAMPBCK PRIPULSEBCK3 56 20 LVL PULSE ROT PRI—RPM—BCK4 ON CONT TIME PRIAMPBCK PRIPULSEBCK4 52 20 PRE—PURGEPOST UPSLOPEDOWN ROTOLY000 000 CCW NEXTSCREENNEXTSCREENNEXTSCREENPREVSCREENUSE OF NEXT/PREV KEYSCONTINUES UNTIL LAST LEVEL IN MEMORY IS SELECTEDLVL PULSE ROT PRIRPMBCK01 ON CONT LVL PULSE ROT PRIRPMBCK01 ON CONT PREVSCREENPREVSCREENNEXTSCREENNEXTSCREENPREVSCREENNEXTSCREENNEXTSCREENPREVSCREENLVL TIME PRIAMPBCK PRIPULSEBCK02 000 000 000 LVL TIME PRIAMPBCK PRIPULSEBCK01 000 000 000 PREVSCREENPREVSCREENNEXTSCREENNEXTSCREENNEXTSCREENPREVSCREENUSE NEXT SCREEN FOR VALUES THEN F KEYSTO CHANGE VALUESUSE SEQ START TO WELDNEXTSCREENNEXTSCREEN三、 焊接號碼列?。汗δ埽悍奖闶褂谜撸菀渍页鏊璧暮附犹?hào)碼。操作：按C鍵再按LIB鍵，按PRINT列印。四、 焊接數據變更：按C鍵再按LIB鍵，把焊接號碼輸入，按ENTER.。輸入正確的焊接數據，焊接完成時，機臺熒幕會顯示YES或NO。REVISE MEMORY TO INCLUDE CHANGESYES NO焊接數據是使用者所需數據按YES,會把焊接數據所定。還要修改焊接數據按NO。五、 焊接前變更焊接數據：按C鍵，按PRO鍵，熒幕顯示，按MODIFY熒幕出現 字，把所需修改的焊接號碼輸入，進入焊接設定步驟。CREATE MODIFY CORY DELETE TRANSFER*** *** *** *** ***六、 清除設定焊接號碼：按C鍵，按PRO鍵，熒幕顯示與變更相同。按DELETE熒幕顯示字，把要清除的焊接號碼輸入，按ENTER二次，完成清除步驟。Model 207 Quick Reference Guide(software revision )“PRO”KEY CREATE 制作新程式 a new weld(key switch must be MODIFY修改現有 an existing weldin “PROGRAM” COPY 拷貝 an existing weldposition) DELETE 清除 an existing weld要制作新程式，鑰匙要 TRANSFER轉移 download entire lib.(to EMM)轉到program的位置 upload 1 weld(from EMM) CALCULATE計算 tungsten length,rotation(RPM)“SET UP”KEY WELD SELECT select 4 welds for access fromsecond screen 選擇焊接程式 remote pendant HEAD CAL焊把校正 Weld head RPM calibration software revision verification “SET UP”KEY PRINT EMM列印焊接號碼 PRINT weld s inEMMsecond screen AMPS/TIME or amps or seconds increments ARC V FAULT 電弧電壓 on/off“SET UP”KEY START LEVEL arc start ampsthird screen SENSORS 1,2,amp。3ON/OFFamp。HIGH/LOW(key switch must PRINTER manual print when “PRINT”keybe in “PROGRAM” is used auto –print automati