注塑模具的保養精華!!(編輯修改稿)
2024-08-28 16:54 本頁面
【文章內容簡介】 n the diagonal line firstly to avoid that eject plate will be jammed if the reset spring is inbuilt in guide post. 頂出板從模板中脫出 ﹐ 放于安全的地方 ﹐ 防止踫傷頂針和斜梢 ﹒ Pull out the eject plate from mold plate and set it on the safe place to avoid damaging eject pine and slanting pin. ?注意點 : Matters needing attention: ?有斜梢時要先卸掉斜梢后的滑塊 (注意編號 ).拉出時要平穩 ,不要踫傷頂針或斜梢 . Separate the sliding block on the back of slanting pin(pay attention to the NO.) if there is it. Pull the sliding block smoothly, don’t damage eject pin or slanting pin. 將模板上的模仁固定螺栓拆下 ﹒ Separate the screw fixed core on the mold plate. ?用兩個較長的螺釘鎖入模仁對角 ﹐ 并交替敲擊兩個螺釘以取出模仁 ﹒ Set two longer screw in the diagonal of core then hit these two screw by turns to pull out the core. ?注意點 : Matters needing attention: ?如果模仁生銹太緊 ,可以先用防銹油浸潤一會 .模仁取出后要注意保護好成型面 . Soak the core with against rust oil if the core with rust. Pay attention to protect the molding surface after pulling out the core. 將模仁上的入子依次取出 ,對于配合比較緊不易取出的入子可以用小銅棒輕輕敲出 . Take out the core pins at last, tap out it lightly with small copper stick if the core pin assembled tightly. ?注意點 : Matters needing attention ?要看清入子、鑲塊、模仁對應部位是否已經標示 ,如果沒有 ,要用磨棒在非成型面上刻上 ,以免混淆 . Confirm the core pin、 embedded lump 、 core are marked or not. If not, mark it with grind stick. 開始公模部分清洗作業 …… Start the clean operation of core…… Clean waterproof ring and water route ?注意點 : Matters needing attention ?要檢查防水圈是否良好 ,對于已經損壞的要及時更換 .防水圈一定要放在工作盤中以免丟失 . Inspect the waterproof rings are good or not. Replace the damaged rings the waterproof rings in the working plate. Clean the rust dirt of core surface ?用油石將模仁外表的銹污清除 . Clean the rust dirt of core surface with oilstone. ?注意點 : Matters needing attention: ?檢查水塞是否密閉良好 ,對于 損壞的水塞及時更換 . Inspect the water stopper is airtight correctly or not, replace the damaged water stopper timely. Clear the hole of embedded lump ? 用小油石裝有鋼刷的電轉除去鑲塊孔中的銹污 . Clean the rust dirt in the hole of embedded lump with small oilstone and electric drill assembled steel brush. 用小油石 (320以上 )除去鑲塊表面的銹 ,并用噴槍清洗 ,吹乾 . Use small oilstone(over 320) to clean the rust on the surface of embedded lump and clean it with spray gun. ?頂針孔或是小型芯孔內的銹污也可用頂針或型芯來清理 ,只要用相應的頂針或者小型芯在孔內反復抽動幾次即可 . Can clean the rust dirt in eject pin hole or small hole of the core with eject pin or core pin, just use the corresponding eject pin or small core pin to twitch several times in the hole. ?用去漬油對模仁和?？驀娤辞瑴Q(jìng)后吹乾 ,尤其是模仁孔內部一定要清洗乾淨 . Spurt cleaning oil on core and mold frame to wash it then dry it, especially clean the hold of core. ?注意點 : Matters needing attention: ?清理的順序一般是先側面 ,再正面 ,再反面 ,最后又正面 . In general the clean order is flank firstly, then front, then reverse side and front again at last. 開始公模部分組裝 …… Start to assemble the core…… 組裝時注意導柱 入子等清潔 ,潤滑 Pay attention to clean and lubricate guide post and core pin etc. when assembling it. Assemble embedded lump and core pin ?用乾淨的手裝上鑲塊及入子 . Use clean hands to assemble embedded lump and core pin. 注意點 : Matters needing attention: ?注意鑲塊入子的編號要和模仁上保持一致 ,裝入后要檢查是否裝正確 . Confirm the no. of embedded lump and core pin
化學相關推薦
鄂ICP備17016276號-1