注塑模具的保養精華!!-資料下載頁
2025-08-01 16:54本頁面
【正文】 例 : For example: 對 PVC模 For PVC mold 除常規作業外 ,每日需用專用中和劑 (SPRAY )均勻噴洗母模面和排氣槽一次 ,待 3分種酸鹼中和后 ,用氣槍吹乾凈模面 ,詳細要求參考 : PVC塑膠模具作業標準 Spurt neutralizer for a special purpose on cavity surface and air vent 1 time, after 3 minutes use air gun clean mold surface. Detailed request according to : PVC plastic mold operation standard 例 : For example: 對客戶有特殊要求之模具 除常規作業外 ,依 成型 SOP 之要求進行保養 ,其重點在清潔與潤滑作業 . Maintain the mold that customer has special request according to molding sop except standard operation, the weightbearing point is cleaning and lubricating. 常用清模作業英語 MOLD CLEANING PROCEDURE ENGLISH 一 .準備清模工具 :噴槍 ,氣槍 ,手電鉆 ,去漬油 ,砂紙 ,碎布 ,油石 ,煤油 ,圓銅刷 ,棉花 . Prepare mold cleaning tools:Engine cleaner,Air gun,electric hand drill,Cleaning oil, broken Cloth Sandpaper,Oil stone,Kerosene,Round copper brush,Cotton. 二 .用油石將公母模入子的油污清除 .(400油石 ) Use oilstone and kerosene to polish dirt on the inserts, which is fixed in mold cavity or core. 三 . 用油石清除排氣槽內瓦斯 .(400油石 ) Use oil stone to polish gas off, which trapped in airvents. 四 .用噴槍吸去漬油清洗模仁入子 ,用棉花擦乾淨 . Use spray gun to clean solvent liquid , wash mold inserts , wipe it off with cotton 五 .拆出水塞將鉆頭裝在手電鉆上 ,清除公母模仁水孔內污垢 . take apart the water plug of mold , Use electric drill to clean the cooling channel in mold core/cavity. 六 .用圓銅刷清洗公模仁內頂針孔 ,斜梢孔 ,用去漬油清洗再用棉花擦拭乾淨 . Use round copper brush to clean ejector hole,lifter hole in the core of mold . Use solvent liquid to clean them, then, wipe them with cotton. 七 .用砂紙拋光頂針 ,去除頂針毛刺 . Use sandpaper to polish ejector pin , remove the burr on ejector pin . 八 .用油石清除模板，頂針板的銹斑及油污 .(大磨石 ) Use oilstone to polish off dust and dirt on moldboard and ejector plate. 附 1: 九 .用小電鉆清洗模板上水孔內污垢 . Use small electric drill to clean the cooling channel of moldboard. 十 .將模仁上的澆道及澆口倒角 . Chamfer runner and gate of mold. 十一 .將閉合器孔倒角拋光 .(三板模 ) Chamfer hole of high loading “P”lock, then polish it . 十二 .將圓頂針磨排氣 .(頂針彎掉 ,需更換 ) Grind airvents on round ejector pin(Change new ejector pins if it is bend). 十三 .將回位梢倒角並拋光 .(夾在車床上 ,用 150砂紙研磨嚴禁戴手套操作 ,違者一律開除 ). Chamfer return pin and polish it (Clamp it on lathe machine to polish with 150 sandpaper), Do not wear gloves when operating machine,offenders will be dismissed ! ) 十四 .將下固定板上四支定位柱拋光 (夾在車床上 ,用 150砂紙研磨 ) Polish 4 locating post of the bottom plate (Clamp it on lathe machine and polish with 150sandpaper). 十五 .在導套與模板之間開排氣 . Grind airvents between moldboard and guide cover. 十六 .將母模板四支拉桿磨板手定位槽 . Grind the four ram of cavity board to be flat for location of the spanner (3plate mold). 十七 .檢查彈簧彈力是否足夠 .(滑塊內彈簧及固位梢之彈簧 ). Check whether the elasticity of the spring is sufficient 附 2: 十八 .檢查 O形環有無破損 . Check whether the “O”ring is damaged. 十九 .檢查母模板四支拉桿長度是否一樣 ,母模板上拉桿孔深度是否一樣 . Check whether the four rams of cavity board is equal in length and whether the ram is equal in depth. 二十 .拋光灌嘴 .(檢查灌嘴是否太小 ,入澆口是否太小 . Polish nozzle (check whether nozzle is too small, whether the nozzle gate is too small). 二十一 .清模后負責人確認並簽名 ,每周五將全部之清模狀況回報並電腦存檔備查 . After tool maintained, person in charge must sign and put the mold condition into puter every Friday to prepare to be checked . 二十二 .現場整理 . put the scene in order. 附 3: The End Thank You
化學相關推薦
鄂ICP備17016276號-1