注塑模具的保養精華!!(參考版)
2025-08-04 16:54本頁面
【正文】 Texture and mirror surface can’t be damaged in cleaning it. 3 禁止在模面直接噴射潤滑油 ,使模面殘留油漬 . Forbid to directly spray lubricant on mold surface. Make sure there is no oil sludge remained on mold surface. 三. 保養后注意 : Attentions after maintenance: 成品外觀有無異常 ,模面有無損傷等不良 , 登記結果于記錄表 . Confirm there is unusual of outer appearance or not, there is injury and defect etc. on mold surface or not. Fill the data on record list. 二 : 細部保養 Details maintenance 細部保養主要內容 Main contents in details maintenance 因各模具的結構不同 , 保養時應依次對模具的模仁 、 模板 、 頂針 、滑塊 、 鑲塊 、 水路 、 導柱等作相應保養 Do corresponding maintenance for core 、 plate 、 eject pine 、 sliding block 、 embedded lump 、 water route 、 guide post in turn because of the difference of mold’s structure. 下面以 電鍍件 為例 ,對細部保養作例圖說明 (因?yàn)殡婂兗?duì)油污敏感性要求比一般塑件要高 .因此 ,清理保養更加徹底 .) Use electroplated part as example to introduce details maintenance. (The maintenance of electroplated part is more thorough than others because its requests of greasy dirt sensitivity is more than others.) 從拆模開始 …. Start from separating mold …. ?首先 ,用天車將模具放在整潔的工作臺面上 ,準備好拆模工具 . Set mold on the clear working table by workshop traveler firstly and prepare the tools. ?然后 ,將公模與母模分開 ,準備拆公模 ﹒ Then separate the core and cavity, prepare to separate core. 公模底板上與?？蜻B接的螺栓卸下 ﹐ 然后將公模固定板和模腳一起拉出 ﹐ 放于一旁 ﹒ Separate the screws that join core’s base plate with mold frame then pull out the stable plate and mold foot together. ?注意點 matters needing attention ?:對于大模具 ,直接拉出比較困難 ,可以先用拔模器拔掉底板上的導柱 .拉出時要平穩 ,防止折彎折斷型芯 . 所卸螺釘導柱等放在預備好的工作盤中 . It is difficult to pull out the big mold. Had better pull out the guide post on the base plate firstly. Pull it smoothly to avoid damaging the core. Must set the screw and guide post in the prepared plate. 頂出底板上的螺釘卸下 ﹐ 拆出頂出底板 ﹒ Separate the screw of eject base plate then separate it. ?注意點 : Matters needing attention: ?如果復位彈簧是在導柱中內置的 ,卸螺釘時應該先卸對角 ,以免頂出板卡死 ,不易脫出 . Separate the screws on the diagonal line firstly to avoid that eject plate will be jammed if the reset spring is inbuilt in guide post. 頂出板從模板中脫出 ﹐ 放于安全的地方 ﹐ 防止踫傷頂針和斜梢 ﹒ Pull out the eject plate from mold plate and set it on the safe place to avoid damaging eject pine and slanting pin. ?注意點 : Matters needing attention: ?有斜梢時要先卸掉斜梢后的滑塊 (注意編號 ).拉出時要平穩 ,不要踫傷頂針或斜梢 . Separate the sliding block on the back of slanting pin(pay attention to the NO.) if there is it. Pull the sliding block smoothly, don’t damage eject pin or slanting pin. 將模板上的模仁固定螺栓拆下 ﹒ Separate the screw fixed core on the mold plate. ?用兩個較長的螺釘鎖入模仁對角 ﹐ 并交替敲擊兩個螺釘以取出模仁 ﹒ Set two longer screw in the diagonal of core then hit these two screw by turns to pull out the core. ?注意點 : Matters needing attention: ?如果模仁生銹太緊 ,可以先用防銹油浸潤一會 .模仁取出后要注意保護好成型面 . Soak the core with against rust oil if the core with rust. Pay attention to protect the molding surface after pulling out the core. 將模仁上的入子依次取出 ,對于配合比較緊不易取出的入子可以用小銅棒輕輕敲出 . Take out the core pins at last, tap out it lightly with small copper stick if t
化學相關推薦
鄂ICP備17016276號-1