【文章內容簡介】 ...................................................................32圖示41. 下部固定螺栓的調節............................................................................42圖示42. 顯示器和信號燈塔的安裝....................................................................42 XY 臺面和Z 軸 的綁帶.................................................................43圖示44. 主壓縮空氣入口Main Air Inlet 接通氣體..............................................43圖示45. 主電源開關接通 ON ............................................................................44圖示51. SWB800 NEO 的啟動裝載畫面..........................................................52圖示52. 系統初始化畫面 (正常情況 ) ................................................................53圖示53. 系統初始化畫面 (發生錯誤情況 ).........................................................53圖示 54. PRS 和 VLL 程序載入（Loading）畫面..............................................54圖示55. USG 初始化畫面................................................................................55圖示 56. Z 軸 原點復歸和 Y 軸向后側移動的畫面..............................................55圖示57. MHS 初始化畫面................................................................................56圖示 58. MHS Home 時檢查 引線框架的 畫面..................................................56圖示59. X, Y, Z 初始化畫面.............................................................................56 初始化畫面...............................................................................56圖示511. 主菜單畫面.......................................................................................57圖示512. “System Config”畫面.........................................................................58圖示513. “Set Data Lock” 畫面.........................................................................58圖示514. “System Login”畫面...........................................................................58圖示515. “User Login” 畫面..............................................................................59圖示516. “About System” 畫面.........................................................................59圖示517. “MISC. Calibration” 畫面.................................................................510圖示518. “Capillary Change Position”畫面....................................................510圖示519. 設置自動模式的畫面.......................................................................511圖示520 . 劈刀更換流程圖畫面.......................................................................512圖示521. 確認劈刀回零的畫面........................................................................513圖示522. 提問劈刀確實更換與否的畫面.........................................................513圖示523. 更換劈刀后的校正 Calibration 順序提示畫面...................................514圖示524. 更換劈刀后未執行 校正Calibration 的錯誤提示..............................514圖示525. “USG Calibration” 畫面...................................................................515圖示526. USG 校正Calibrtion 結果圖表圖.....................................................516三星全自動金球焊線機 800 系列 操作手冊10圖示527. USG 校正 Calibration 歷史記錄信息畫面....................................... 517圖示 528. “Setup Crosshair Offset”畫面 (2 倍率攝像機) ................................ 518圖示 “Touch Parameters”畫面.................................................. 519圖示 ................................................................. 519圖示 ........................................................................... 520圖示 高度 “Setup Teach EFO Height”畫面.............................. 521圖示 533. EFO 刀片設置................................................................................ 521圖示 534. EFO 刀片高度設置........................................................................ 522圖示 535. 劈刀使用量計數回零設置畫面........................................................ 522圖示 ........................................................................... 523圖示 “Teach Bond Heights”畫面........................................ 524圖示 538. 示教焊線高度設置Teach Bond Height 畫面................................... 525圖示 “Lighting amp。 Crosshair”畫面.................................... 525 “Change Crosshair”畫面........................................... 526”Set Lighting Level”畫面.................................................... 526圖示 “Set Light”設定........................................................................ 527圖示 “Bond Head Menu” 畫面.................................................. 527圖示 544..半周期 “HalfCycle”畫面................................................................. 528圖示 545. 半周期中形成金球的畫面................................................................ 529圖示 “Touch Parameters”畫面.................................................. 529圖示 “AUTO Condition”畫面..................................................... 530圖示 548. “PRS Condition” 畫面..................................................................... 531圖示 549. 多排器件校準以及焊線順序............................................................ 532圖示 550. 視點搜尋配置 “EYE Search Configuration”畫面............................. 533圖示 551. 跳過不合格Reject SKIP 功能設置畫面.......................................... 535圖示 Reject Skip 的數量超過規定量時的錯誤提示................ 535圖示 553. PRS SKIP 功能設置畫面................................................................ 537圖示 軸的器件跳過 Device Skip by Z Touch 菜單畫面.................. 538圖示 Touch Position Parameter 的意義............................. 538圖示556. Z 軸觸點式跳過 Device Skip 時發出的錯誤提示............................ 539圖示 557. “WBMS Configuration” 畫面........................................................... 540圖示558. Ball Teach 菜單畫面...................................................................... 542圖示 559. Ball Teach 的確認畫面.................................................................... 543圖示 560. “Bond Height Configuration”畫面................................................... 544圖示 561. “Error Detect Configuration”畫面.................................................... 544手冊目錄11圖示 ......................................................