【文章內容簡介】 46 關閉電 源 ....................................................................................................................................... 46 二、 SGI ORIGIN 2020 SERVER的開啟與關閉 ...................................................................................... 47 開啟電源 ....................................................................................................................................... 47 啟動系統 ....................................................................................................................................... 47 關閉系統 ....................................................................................................................................... 47 關閉電源 ....................................................................................................................................... 48 IRIX 系統管理 第 5 頁 共 49頁 第一章 IRIX 安裝及配置 一、系統參數： 硬件： O200 CPU 類型： IP27， 180MH 軟件： (最小安裝需 4 張光盤 ) IRIX Installation Tools IRIX Foundation 1 IRIX Foundation 2 IRIX Applications 二、分區： 使用光盤啟動系統進行分區： SGI O200出廠時已經預裝操作系統，因此系統硬盤不必重新分區。增加的硬盤改變分區可以在操作系統正 常啟動后使用“ fx x”命令重新分區。 如系統硬盤是空的硬盤，進行如下步驟： System Maintenance Menu 1) Start System 2) Install System Software 3) Run Diagnostics 4) Recover System 5) Enter Command Monitor IRIX 系統管理 第 6 頁 共 49頁 Option? 5 Command Monitor. Type exit to return to the menu. 插入“ IRIX Installation Tools”光盤 hinv “查看系統硬件配置” System SGIIP27 “ IP27CPU類型” 1 180 MHz IP27 Processors Main memory size: 128 Mbytes Integral SCSI controller 0 Integral SCSI controller 1 Integral Fast Ether IOC3 serial port Disk drive: unit 1 on SCSI Controller 0, (dksc(0,1,0)) CDROM: unit 6 on SCSI Controller 1, (cdrom(1,6,7)) “ cdrom(1,6,7)光驅在 1號 控制器 6單元” boot f dksc(1,6,8)sash64 dksc(1,6,7)stand/ x sash版本 fx版本 “ sash、 fx 版本由 CPU 類型決定” 896+115812+16653+3832 entry: 0xa8000000012a7e2c 2112+115940+28805+10680 entry: 0xa800000000fd3eac SGI Version ARCS BE64 Apr 30, 1998 fx: devicename = (dksc) “ dksc是 SCSI硬盤名稱” fx: ctlr = (0) “ SCSI控制器號” fx: drive = (1) “單元號” ...opening dksc(0,1,0) “ dksc(0,1,0)系統硬盤” 注：對某個硬盤分區，改變 ctlr、 drive 參數 ...drive selftest...OK Scsi drive type == SGI QUANTUM XP34550WLXY7 please choose one (? for help, .. to quit this menu) [exi]t [d]ebug/ [l]abel/ [a]uto [b]adblock/ [exe]rcise/ [r]epartition/ fx r partitions “系統硬盤由操作系統自動分區” part type blocks Megabytes (base+size) 0: xfs 1052672 + 7835871 514 + 3826 1: raw 4096 + 1048576 2 + 512 8: volhdr 0 + 4096 0 + 2 10: volume 0 + 8888543 0 + 4340 capacity is 8888543 blocks please choose one (? for help, .. to quit this menu) IRIX 系統管理 第 7 頁 共 49頁 [ro]otdrive [o]ptiondrive [e]xpert [u]srrootdrive [re]size fx/repartition .. please choose one (? for help, .. to quit this menu) [exi]t [d]ebug/ [l]abel/ [a]uto [b]adblock/ [exe]rcise/ [r]epartition/ fx exi Installing PROM Device drivers ............ Walking SCSI Adapter 0 (/hw/module/1/slot/MotherBoard), (pci id 0) 1+ 2 3 4 5 6 7 8 9 10 11 12 13 14 15 = 1 device(s) Walking SCSI Adapter 1 (/hw/module/1/slot/MotherBoard), (pci id 1) 1 2 3 4 5 6+ 7 = 1 device(s) Initializing PROM Device drivers .......... DONE Checking hardware inventory ............... DONE 附： repartition子命令： rootdrive Repartition as system drive with root,swap,vh,and vol partitions usrrootdrive Repartition an oldstyle system drive with root partition,swap, usr,vh,vol optiondrive Repartition as option drive with one large efs/xfs,vh,and vol partitions resize Resize the standard partitions (depending on whether you choose root,usrroot,or option drive) expert Use expert mode for be used for creating IRIX分區類型 分區名稱 分區號 root 0 swap 1 usr 6 (none) 7 volhdr 8 (none) 9 volume 10 xfslog 15 三、系統安裝： System Maintenance Menu IRIX 系統管理 第 8 頁 共 49頁 1) Start System 2) Install System Software 3) Run Diagnostics 4) Recover System 5) Enter Command Monitor Option?2 Installing System Software... Press Esc to return to the menu. 1) Remote Directory 2)[Local CDROM] *a) Local SCSI CDROM drive 6, on controller 1 Enter 12 to select source type, a to select