【正文】 會造成產品結構上的缺陷。 圖 34是兩種方案的流動前沿溫度圖 常州工學院機電工程學院畢業設計論文 9 （ a） (b) 圖 34為兩種方案的流動前沿溫度 兩種方案的流動前沿溫度： 方案（一）的溫度范圍 ～ （ c? ）； 方案（二）的溫度范圍 ～ （ c? ）。 方案二：一個澆口放在工件內側兩個圓之間。從塑料的壁厚上 來看，壁厚最大處 3mm,最小處為 1mm,壁厚差為 2mm,較為均勻。 零件一側沿脫模方向設計有脫模斜度約為 2176。在學習了課本知識的基礎上達到理論與實際相結合的升華，提高自己的獨立動手能力。 根據 塑 件的結構特點進行模具方案論證 ， 并進行模具總體裝配圖的設計 ， 主要成型零件的設計 與計算，并完成裝配圖和零件圖的繪制。注塑制品已呈現自動化生產，對注塑成型機可以進行遠距離操作或無人操作，成型機可以根據生產監測信號實時調整成型工藝條件，從而能從根本上保證塑料制品的成型質量常州工學院機電工程學院畢業設計論文 2 不發生問題。 （ 1） 初級階段： 30年代以前，科學家研究成了酚醛塑脂，硝酸纖維素及醋酸纖維素的塑料，它們的工業特征僅是間歇法，小批量生產。該模具采用潛伏式澆口和側向抽芯機構，一模兩腔。 關鍵詞： 注射模具 一模兩腔 模具設計 模擬分析 常州工學院機電工程學院畢業設計論文 ii ABSTRACT My graduation project is the injection simulation analysis and the design of the injection mold of the side cover of the disinfect a structure characteristics of the plastic part were analyzed. The Moldflow software was used for the simulation analysis and optimization of the gate position for the plastic part. By optimizing the process parameters, the defects of the injection molding were successfully avoided. Based on the simulation result, the structure designing and the material selection of its injection mold had been finished. The injection mold with two cavities adopted the hidden gate system and side corepulling CAE optimizing with mold design could shorten the mold developing cycle, reduce the product development cost and enhance the product quality. The mold was convenient to operate , with proper structure and high efficiency. Keywords: Plastic mould two cavities of the mold mold design simulation analysis 常州工學院機電工程學院畢業設計論文 I 目錄 言 ........................................................... 1 .........................................................................................................................................................................1 ................................................................................................................................................................1 ....................................................................................................................................................1 ....................................................................................................................................................2 ....................................................................................................................................................2 ...........................................................2 .....................................................2 .................................. 3 2． 1塑料的原材料分析 .............................................................................................................................................3 ......................................................................................................3 ...........................................................3 .........................................................4 .............................................................4 2． 3塑料的注射工藝參數的確定及模架的選擇 ....................................................................................................4 3. MOLD FLOW 模擬分析 ................................................ 7 3． 1網格劃分和修改結果 .........................................................................................................................................7 ...........................................................................................................................7 .....................................................8 ...................................... 12 ..................................................................................................................................................... 12 ..................................................................................................................................................... 12 ........................................................................................................................................ 13 ................................................................................................................................................. 13 ． 1主流道的設計 .............................................................13 ......................................................14 ..............................................................14 ................................................................15 、冷卻系統的設計與計算 ........................................ 16 ................................................................................................................................................. 16 .................................................................................................................................... 17 ................................................... 19 ............................................................................................................................................. 19 常州工學院機電工程學院畢業設計論文 II ................................................................................................................................ 19 ......................................................19 型腔壁厚和底板厚度的計算 ...........................................................................