叉車液壓缸畢業設計(已修改)
2024-12-09 16:37 本頁面
【正文】 ，液壓缸的設計包括了系統工作壓力的選定、液壓缸內徑和外徑的確定、活塞桿直徑和 活塞直徑的確定、液壓缸壁厚的計算、缸蓋厚度的確定、缸體長度的確定、緩沖裝置的計算以及活塞桿穩定性的驗算。本設計應用經驗設計法和計算機輔助工程技術完成，先依據經驗公式計算，確定了液壓缸安裝方案，設計了液壓缸活塞及活塞桿尺寸參數，校核匹配的連接螺栓、銷軸等。最后用繪圖軟件 CAD完成液壓缸裝配圖。 關鍵詞：叉車、提升液壓缸、液壓缸設計 I Abstract ABSTRACT This is the subject of internal bustion forklift lifting hydraulic cylinder design, the hydraulic cylinder design including the working pressure of the system is selected, the hydraulic cylinder inner diameter and outer diameter of the piston rod and the piston diameter, diameter determination, hydraulic cylinder wall thickness calculation to determine the thickness of the cylinder block, cylinder head, length, buffer device is calculated and the piston rod stability checking. Design and application of the experience design method and puter aided engineering technology, according to the empirical formula, determine the hydraulic cylinder installation project, design of hydraulic cylinder piston and piston rod size parameters, check matching bolt, pin. Finally with the drawing software CAD plete hydraulic cylinder assembly drawing. Key words: forklifts, lifting hydraulic cylinder, hydraulic cylinder design II 目錄 目 錄 1. 引 言 ............................................................ 1 ....................................................... 1 提升液壓缸簡介 .................................................. 1 本設計的主要緩沖裝置計算 ................................................. 7 3. 液壓缸的校核 ..................................................... 9 ................................. 9 ................................................. 9 ，缸體螺紋處的拉應力 .................... 10 .................................. 10 ........................................ 11 .................. 錯誤！未定義書簽。 4. 液壓缸的結構 .................................... 錯誤！未定義書簽。 缸體與缸蓋的連接 形式 ........................... 錯誤！未定義書簽。 .......................... 錯誤！未定義書簽。 活塞桿導向部分結構 ............................. 錯誤！未定義書簽。 密封裝置的選用 ................................. 錯誤！未定義書簽。 間隙密封 ..................................... 錯誤！未定義書簽。 活塞環密封 ................................... 錯誤！未定義書簽。
公司管理相關推薦
鄂ICP備17016276號-1