焊接材料質量管理規定(已修改)
2025-06-04 18:17 本頁面
【正文】 目錄Table of Contents1 范圍 61 Scope 62 引用標準 62. Normative references 63 職責 83. Responsibilities 84 采購 84. Purchase 85 驗收 9 驗收項目 9 包裝檢驗 9 質量證明書檢驗 95. Acceptance inspection 9 Inspection items 9 Packing inspection 9 Inspection of quality certificates 9 外觀檢驗 9 成分及性能試驗 10 檢驗結果的認可 10 驗收標記 10 Exterior inspection 10 Composition and performance test 10 Approval of inspection results 10 Inspection mark 106 入庫 106. Warehousing 117 庫存保管 11 存放條件 117. Storage 11 Storage conditions 11 庫存期間的檢查 12 Inspection during storage 128 出庫 128. Distribution 129 使用過程中的管理 13 一般要求 139. Management during use 14 General requirements 14 烘干、保溫及清理 14 Drying, heat insulation and cleaning 14 識別標志 15 焊接材料的回收 15 Identification mark 15 Recovery of welding materials 15 回收的焊接材料的烘干 16 焊劑的重復使用 16 Dry of recovery welding materials 16 Repeated use of welding flux 16焊接材料質量管理規程Corporate Management Rules for Welding Material Quality Control1 范圍本標準規定了焊接材料,包括焊條、焊絲、焊劑、合金粉末、襯墊及焊接用氣體等，在采購、驗收、庫存保管及使用過程中的管理要求。為了保證焊接材料的使用性能，應具備必要的貯存、烘干、清理設施，建立可靠的管理規程并嚴格執行。本標準適用于焊接生產中，上述這些焊接材料的質量管理。1 ScopeThis Standard specifies management requirements of welding materials (., welding electrode, welding wire, welding flux, alloy powder, backing and welding gas) during purchase, acceptance, warehousing and use. In order to ensure service performance of welding materials, necessary storage, drying and cleaning installations shall be made available, and reliable management specifications shall be established and strictly observed.This Standard applies to quality management of the said welding materials during welding operation.2 引用標準下列標準所包含的條文，通過在本標準中引用而構成為本標準的條文。標準出版時，所示版本均為有效。所有標準都會被修訂，使用本標準的各方應探討使用下列標準最新版本的可能性。GB/T51171995 《碳鋼焊條》 GB/T51181995 《低合金焊條》 GB/T9831995 《不銹鋼焊條》 GB/T9842001 《堆焊焊條》 2. Normative referencesThe following standards contain provisions which, through reference in this Standard, constitute provisions of this Standard.At time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below.GB/T51171995 Carbon steel electrodesGB/T51181995 Low alloy steel electrodesGB/T9831995 Stainless steel covered electrodesGB/T9842001 Hardfacing electrodes for shielded metal arc weldingGB/T 13814—92 《鎳及鎳合金焊條》GB/T 15620—1995 《鎳及鎳合金焊絲》GB/T149571994 《熔化焊用鋼絲》 GB/T81101995 《氣體保護電弧焊用碳鋼、低合金鋼焊絲》 GB/T100452001 《碳鋼藥芯焊絲》 GB/T174931998 《低合金鋼藥芯焊絲》 GB 4242—85 《焊接用不銹鋼絲》GB/T52931999 《埋弧焊用碳鋼焊絲和焊劑》 GB/T 13814—92 Nickel and nickel alloy covered welding electrodesGB/T 15620—1995 Nickel and nickel alloy wires for welding rodsGB/T149571994 Steel wires for melt weldingGB/T81101995 Welding electrodes and rods for gas shielding arc welding of carbon and low alloy steelGB/T100452001 Carbon steel flux cored electrodes for arc weldingGB/T174931998 Low alloy steel flux cored electrodes for arc weldingGB 4242—85 Stainless steel wires for weldingGB/T52931999 Carbon steel electrodes and fluxes for submerged arc weldingGB/T124702003 《低合金鋼埋弧焊用焊劑》 GB104332002 《電弧螺柱焊用園柱頭焊釘》 GB/T48422006 《純氬》 GB/T60521993 《工業用二氧化碳》 HG/T25371993 《焊接用二氧化碳》 CCS 規范 材料焊接部分DNV 規范 材料焊接部分ABS 規范 材料焊接部分GL 規范 材料焊接部分BV 規范 材料焊接部分LR 規范 材料焊接部分GB/T124702003 Lowalloy steel electrode
環評公示相關推薦
鄂ICP備17016276號-1