【正文】 anel or outgoingline panel are diagram of basic switchgear panel，there are other derivative diagram，for example ,contact panel or metering panel .in addition，There are so many diagram of the switchgear panel with stationary type load switch、（SF6）VCB truck、VC truck、Disconnect truck. The panel has two maintenance modes. That is singleface maintenance and doubleface maintenance. The detail of structure and main ponents, can reference order document. Enclosure and clapboard開關柜的外殼和隔板由優質鋼板制成，具有很強的抗氧化、耐腐蝕功能，且剛度和機械強度比普通低碳鋼板高。出現內部故障時，高壓室內氣壓升高，由于柜門已可靠密封，高壓氣體將沖開壓力釋放板釋放出來。低壓室D裝配成獨立隔室，與高壓區域分隔開。卸下緊固螺栓就可移開水平隔板，便于電纜密封終端的安裝。當手車從運行位置向試驗/隔離位置移動時，活門會自動蓋住靜觸頭，反向運行則打開。VCB truck is installed in VCB vault B with track, may move in the middle of the position to service and test/disconnected. While the truck move from service position to test/disconnected position, the valve can cover unmove contact in selfmotion, open when moving reverse. The truck can be operated when the truck vault door is closed, while you can watch the position of the truck, on (VCB tripping)/off(VCB closing) push knob in the truck, close and open indicator and charging/releasing indicator by inspection window. 斷路器手車 VCB truck手車可采用手動進行移動。具有彈簧觸頭系統的觸臂裝在斷路器的極柱上，當手車插入到運行位置時起電氣聯接作用。手車剛插入開關柜就固定在試驗/隔離位置，同時也可靠地聯接到開關柜的接地系統。除真空斷路器外，手車可配真空接觸器、隔離裝置和計量設備等。矩形的分支母線直接用螺栓聯接到主母線上，不需任何聯接夾。套管板和套管將柜與柜之間的母線隔離起來，并有支撐作用。The bus bar from one switchgear to the other switchgear is fixed with the bushing and the ramus bus .The ramus bus is connection to the main bus with the bolt, it needn’t any clip. All bus and the ramus bus are covered with pyrocondensation bushing. The panel of bushing and bushing are isolated between the switchgear and the switchgear. And it has the effect on supporting.電纜室（圖3/1）Cable partment（drawing 3/1）電流互感器和接地開關裝在電纜室后部。當電纜室門打開后，有足夠的空間供施工人員進入柜內安裝電纜（最多可并接6根）。底板中穿越一、二次電纜的變徑密封圈開孔應與所裝電纜相適應，以防小動物進入。CT and earth switch are installed on the back of the Cable Compartment. The Surge arrester is also installed on the Cable Compartment. When the truck and the horizontal panel are moved .There is enough room so that the worker install the cables (the most is 6).The bottom of panel that lie on the ining of cable in made of the stainless steel panel，It is uncork, disassembly so that working on the local. The airplane of panel where is together secondary cable make sure as same as the installed cable prevent the small animal being into it.For the cable trench in humidity，It is suggested that the switchgear is airproofed with fireproofing mud and epoxide resin.低壓室（圖3/3/2） Lowvoltage partment (figure 3/3/2)開關柜的二次元件裝在低壓室內及門上。低壓室側板上有控制線穿越孔，以便控制電源的聯接。聯鎖裝置地功能如下：A series of interlocks are provided to prevent mishandling, thus protecting both personnel and switchgear itself. The function of interlocks is following: 216。在這種分 閘狀態下，反向移動也行（機械聯鎖）。 手車已完全處于試驗或運行位置時，斷路器才能合閘（機械和電氣聯鎖）。 手車在試驗或運行位置而沒有控制電壓時，斷路器不能合閘，僅能手動分閘（電氣聯鎖）。 手車在運行位置時，控制線插頭被鎖定，不能拔出。 手車在試驗/隔離位置或移開時，接地開關才能合閘（機械聯鎖）。 接地開關關合時，手車不能從試驗/隔離位置移向運行位置（機械聯鎖）。 可在手車和/或接地開關操動機構上安裝附加聯鎖裝置，如閉鎖電磁鐵，用戶在訂貨時應提出要求。母線、緊固件和附件是單獨包裝的。特別是海上運輸，即使是裝在集裝箱內，也應用塑料薄膜袋將開關柜封裝起來，放入合適的干燥劑以防受潮。每臺開關柜都裝有4個吊耳。 吊車，叉車或人工起吊架。 用吊車裝載Loading with crane216。Lifting rope should have enough carrying capacity. The unlock width of lifting hook should not less than 30mm.216。以上。.216。The lifting lugs are permitted to have relevant bend when the switchgears are lifted. Delivery and intermediate storage開關柜到達現場時，收貨人有責任（但不限于）做如下工作：When the switchgears are in locale, the duties of the consignee include the following (not only):216。Inform CJEC service engineers to join the work of opening box, checking and accepting.216。開關柜的標記及合格證是否正確齊全，有無說明書。如果需要中間存儲時，還要放入干燥劑，重新密封。 詳細記錄任何短缺、缺陷和運輸損傷，并及時通知有關機構。Please notice: The delivery should be placed on location without any damage to switchgears and installation materials when intermediate storage.開箱程序如下：The sequence of opening box is following:首先拆開包裝箱的頂板，再拆開四周的側板，最后卸掉開關柜與底盤聯接的螺栓。利用柜頂?shù)乃闹坏醵?，將開關柜垂直吊起使其與底盤脫離。注意在移動過程中，不得有較重的撞擊與振動。 儲藏室應干燥，通風良好。 室內溫度不低于25176。C216。No other dangerous environment infections.216。Storage switchgears erectly.216。Switchgears can not be piled.216。Do not be knockingout or damage packaging.216。必須保持空氣流通以防腐蝕。 有規律地按時進行凝露檢查，直至安裝工作開始。 運輸單元存放在干燥，防潮防損壞的地方。 檢查包裝有無破損。 從包裝之日算起，超過保管期限時，包裝的保護功能可能會喪失，若還需存放，則要采 取適當措施。Make sure of the correct installation sequence and highest installation quality, local installation should be carried out by fully trained personnel, or inform CJEC engineers to guide and ward in locale. General request of installation locale配電室的土建工程必須完工經過驗收后，并配備照明和安裝用電源，通風裝置。電纜溝應按各地電纜工區的具體要求施工。配電室的天花板高度不應低于3000mm，必須保證滿足IEC規定的戶內開關柜工作條件，包括戶內溫度條件。KYN2812開關柜可以靠墻安裝，以節省占地面積，但如果條件許可，仍建議設計配電室平面布置時，按雙面維護考慮，使開關柜后蓋板到隔墻之間以及開關柜兩側到隔墻之間均留出適當?shù)陌惭b維修通道。若開關柜是雙排面對面布置，兩排開關柜之間距離建議不小于2500mm。當敷設基礎時，應遵守GB規定，尤其是直線度和平面度的允許公差，這是開關柜安裝完美的先決條件。It is relative suitable to install the switchgear at the foundation frame builting in the floor of distribution house or elevated auxiliary level ground. Build the foundation according to GB regulation, especial the permission tolerance, it is precondition for full installation of the switchgears. The switchgears foundation construction must be accord with relative item to power construction and technical regulation for checking and accepting.. 1以配電室地板作為基礎Basing on the floor of distribution house開關柜數量少，重量較輕時，可直接安裝在配電室地板上。如果需要，在安裝調整時可在開關柜下面插入合適的墊片。建議由電氣安裝單位承擔基礎框架的制作和埋設。For figure 5/5 showing, the inbuilt foundation frame of switchgear build require to take the way of the second grouting, after finishing the Civil work construction, carry through the foundation frame building. It is advised to able to do that electric installation unit are charged with the foundation frame facture and building. It is agree with blueprint drew accord to manufactory requests to process the concrete project’s foundation frame.土建施工時開關柜基礎標高應考慮預留基礎框架槽鋼的高度，并略有余量，見圖5/6?；A(chǔ)框架縱向槽鋼的外延距離應與開關柜本體框架的尺寸一致。用鋼墊片調整。并要求基礎框架的頂面應高于配電室最終地坪標高約3至5