【正文】 Check— P1 P3 P4 P5 P6 P7 P8 P1: H point X,Y,Z coordinates at design position 設計位置 H點 X,Y,Z坐標 。其它尺寸顯示座椅對稱性 Guideline: 35 H+400mm H+100mm H+300mm H+200mm H+0mm H+500mm 2023/3/23 23 Guideline: 35 H+0 OK Comfort Check— C1 2023/3/23 24 Guideline: 35 H+100 Comfort Check— C1 OK 2023/3/23 25 Guideline: 35 H+200 OK Comfort Check— C1 2023/3/23 26 Guideline: 35 OK Comfort Check— C1 H+300 2023/3/23 27 Guideline: 35 H+400 OK Comfort Check— C1 2023/3/23 28 Guideline: 35 H+500 OK Comfort Check— C1 2023/3/23 29 Comfort Check— C3 C3:Sections through the cushion every 100mm starting from H point perpendicular to track or thigh, mark min meat to metal dimension. Other dimension show seat symetrical. 從 H點沿垂直滑道或大腿每一百毫米截面，每個截面顯示最小 MTM距離。 (帶扣側 ) 2023/3/23 11 Safety Check— S16 S16:SIAB location 側向安全氣囊位置 Guide line: 1. SAB與座椅表面的尺寸滿足右邊圖示尺寸，設計座椅撕裂線時，氣囊距撕裂線距離應為 20～ 40mm。 (非帶扣側 ) 2023/3/23 10 Safety Check— S10 S10:Safety belt anchorage zone (whole travel window) 安全帶系統安裝區域（所有行程范圍） o GB14167:α值應 為 45176。2023/3/23 1 GB11550 汽車座椅頭枕性能要求和試驗方法 GB15083 汽車座椅系統強度要求及試驗方法 GB14167 安全帶安裝固定點 GB8410 汽車內飾材料的燃燒特性 GB11552 汽車內部突出物 GB11551 關于正面碰撞乘員保護的設計規則 GB20231 關于側面碰撞乘員保護的設計規則 ECE R14 Safety Belt Anchorages ECE R17 The Seats, Their Anchorages and any Head Restraints ECE R21 Interior Fittings ECE R44 Child retrain systems ECE R94 Frontal collision ECE R95 Later collision Heavy Metal Requirement 必須滿足的法規 Required Regulations 2023/3/23 2 Safety Check 2023/3/23 3 Safety Check— S1,S2 S1 S2:Distance from H point to headrest top surface at headrest full down/up position along torso angle 沿著靠背軀干線，從 H點到頭枕最低 (最高 )位置的上表面的距離 . OK GB150832023 / ECE R17— 高度 750mm以下無使用位置，頭枕高度不應低于 800mm 頭枕處于最低位置 Headrest in lowest position 頭枕處于最高位置 Headrest in highest position 2023/3/23 4 Safety Check— S3 S3:Section through headrest perpendicular to torso line and 65mm downward from headrest top surface 垂直靠背軀干線，從頭枕上表面 65mm向下的頭枕截面 GB150832023 / ECE R17— ≥170mm for the width of head restraint OK 2023/3/23 5 Safety Check— S6 S6:Distance from headrest top surface to headrest frame 從頭枕上表面到頭枕骨架的距離 NA fmvss 202a 25mm 2023/3/23 6 Safety Check— S5,S7 S7:IIHS requirement on headrest by using HRMD 用頭型測量設備（ HRMD）對 IIHS要求的校核 NOK Middle Position Whiplash score issue, CF11 17mm Low Most Position 2023/3/23 7 Safety Check— S8 S8:Requirement of head restraint gaps and clearance to seat back (upper most and lowest position) 頭枕間隙以及頭枕到座椅靠背間隙檢查（頭枕最高和最低位置） GB150832023 FMVSS 202a:頭枕最低位置與靠背間隙不大于 25mm或 165直徑的球相切點間距不大于 60mm STO change to less than 15mm(CF11 14mm) Headrest Carry over from CF14K 2023/3/23 8 Safety Check— S9 S9:Section through headrest showing the impact angle of 45 degrees from rear side 頭枕截面顯示從后部向頭枕的 45度角碰撞 OK 2023/3/23 9 Safety Check— S10 S10:Safety belt anchorage zone (whole travel window) 安全帶系統安裝區域（所有行程范圍） o GB14167:α值應 為 30176。 ~ 80176。 ~ 80176。 2. SAB與座椅 STO面的距離應為 10～ 15mm Carry over CF11 Back Frame and Airbag 2023/3/23 12 Safety Check— S17