【正文】 4 6 22 8 38 8 38 10 60 10 80 10 100 10 100 12 150 12 200 12 325 12 CLAMPING TORQUE STEELCOPPER lbinNmlbinNm 12Table 11. Wire Sizing For Main CircuitSECTION A. 230V DRIVE HPMODEL NO. TERMINAL SYMBOLTERMINAL SYMBOLRATINGGPD505V–TERMINAL WIRE SIZE WIRE SIZE TERMINALSCREWAWGMM2 SCREW AWGmm2A003,A006A008A011A017A027,A036A054A068A080A104A130A160A192A248A312L1 (R), L2 (S), L3 (T), , 197。C) (for protected chassis drives), orbelow 104176。 this will ensure sufficient air space for cooling.Make sure air entering the drive is below 113176。 M2) .............................................. 5 3 7Overtorque Detection ............................................................... 5 3 1PID Control ................................................................................ 5 4 1Reset Codes。 MC。 Lower Limits ............................. 5 1 7Frequency Reference Loss Detection ..................................... 5 1 8Frequency Reference Retention ............................................... 5 1 8 . 1Jog Reference .......................................................................... 5 1 8 . 22345Release Date07/15/97viiviii(THIS PAGE INTENTIONALLY BLANK)CONTENTS – Co n t i n u e dPARAGRAPHSUBJECTPAGE67App. 1App. 2App. 3App. 4App. 5App. 6App. 7Local/Remote Changeover ........................................................ 5 1 9Modbus Control ......................................................................... 5 2 0Miscellaneous Protective Functions ......................................... 5 2 2 . 1Momentary Power Loss Ridethru ............................................ 5 2 2 . 2Multifunction Analog Monitor Output (Term. AM amp。 Horsepower RangeRATEDINPUT CURRENTRATING (AMPS) 6 8 11 27 36 54 68 80104130160192248312 8 1114 21 27 344152658096128180240302380506675NOMINAL HORSEPOWER (120% OL) 1 / 2 3 5 / 10 15 20 25 30 40 50 60 75 100 125 1/2 3 5 10 15 20 25 30 40 50 60 75 100125 / 150 200 250 300350 / 400 500MODEL NO. GPD505VA003A006A008A011A017A027A036A054A068A080A104A130A160A192A248A312B001B003B004B008B011B014B021B027B034B041B052B065B080B096B128B180B240B302B380B506B675230V460VvWARNINGDo not touch circuit ponents until main input power has been turned off and“CHARGE” lamp is extinguished. The capacitors are still charged and can bequite dangerous.Do not connect or disconnect wires and connectors while power is applied to thecircuit.CAUTIONKnow your application before using either Initialization function of n001 . Thisparameter must be set to 0 , 1 , 2 , or 3 to operate the drive. (Seeparagraph for additional information.) 8 = Factory 2Wire Control Initialization (Maintained RUN Contact) 9 = Factory 3Wire Control Initialization (Momentary START/STOP Contact)Entering either Initialization code resets all parameters, and automatically returnsn001 setting to 1 . If the GPD 505 is connected for 3Wire control and thisconstant is set to 8 (2Wire Control Initialization), the motor may run in reversedirection WITHOUT A RUN COMMAND APPLIED. Equipment damage or personalinjury may result.CAUTIONWhen drive is programmed for autorestart (n056 = 1 – 10 ), the motor mayrestart unexpectedly — personal injury may result.IMPORTANTWiring should be performed only by qualified personnel.Always ground the GPD 505 using ground terminal (). See paragraph , Grounding.Verify that the rated voltage of the drive matches the voltage of the ining power.Never connect main circuit output terminals T1, T2, and T3 to AC main circuit power supply.All parameters have been factory set. Do not change their settings unnecessarily.Do not perform a “HIPOT” or withstand voltage test on any part of the GPD 505. Equipmentuses semiconductors and is vulnerable to high voltage.The Control PCB employs CMOS ICs which are easily damaged by static electricity. Useproper electrostatic discharge (ESD) procedures when handling the Control PCB.Any modification of the product by the user is not the responsibility of MagneTek, and willvoid the warranty.Data subject to change without notice.viCONTENTSPARAGRAPHSUBJECTPAGEGPD 505 SIMPLIFIED STARTUP PROCEDURE ..................... iCURRENT RATINGS amp。 see Appendix 7.(5) The user cannot program these two parameters. They are used for the automatic Elapsed Timer function of the drive。 R EF LEDs turn on.6 . Calibrate manual speed pot for maximum speed at maximum rotation. With switch S1 in the “Stop” position, press D I S P L key repeatedly until the F r e f LED turns on. The display will indicate the bined setting of the trim and manual speed pots。 7 for fault correction procedure.INSTALLATION OF EXTERNAL RUN/STOP SWITCH AND SPEED POTENTIOMETERSIMPORTANT: Complete the INSTALLATION and KEYPAD OPERATION instructions beforeattempting external control.1 . Disconnect power, remove drive front cover with Digital Operator, and wait for “CHARGE” light to go out.2 . Refer to the diagram below and connect a switch to terminals S1 and SC using two conductor shielded wire. This circuit is 24Vdc, very low current。 the display now shows output frequency (speed). The next function is I o u t, and indicates drive output current (in Am