出口產品運輸產品包裝標準(最終版)-文庫吧資料
2025-07-20 18:36本頁面
【正文】 e between the side pillar of the inside側支柱的內面間距離The distance between the side pillars inside側面上、下框兩外緣間的距離On the side, the distance between the two outer box內長+（端柱厚+端外板厚）2Inseam length+ ( thickness of end post +thickness of planking ) *2內寬+（側柱厚+側外板厚）2Inner width + ( thickness of column+ thickness of test plate) *2內高+頂蓋厚+底座厚（滑木厚+輔助滑木厚+底板）Inner height+ thickness of header+ thickness of base ( thickness of slippery wood+ thickness of assistant slippery wood+ floor) Dimensional deviation木構件寬度與厚度的尺寸偏差按表5規定。According to the provisions of table 4, we express packing size with the size or outside dimensions.表4 包裝箱的尺寸表示Table 4 Dimensions indicated of packing case名稱 name內 尺 寸Inside stacking load mainly refers to the upper part of the load supported by side of the frame. Therefore, when placed the goods smaller than top width directly, top load and stacking load militate. When placed the goods same as the top width or used the right goods is larger than the top width, stacking load mainly militate.為防止內裝物因接觸框架木箱的面而引起損傷,在其間充填緩沖材料或留出適當間隙,單面間隙30mm。因此，直接放置比頂蓋寬度小的貨物時，頂蓋載荷和堆碼載荷發生作用，放置與頂蓋寬度相同的貨物或使用比頂蓋寬度大的合適貨物時，主要是堆碼載荷發生作用。For stacking load to the side, it is stipulated in the roof area such as table 3.表3 堆碼載荷Table 3 Stacking load內裝物重量(kg) weight of builtin objects (kg)堆碼載荷kPa（kgf/ m2）stacking load kPa （kgf/ m2）≤5000(1020)5000~10000(1530)10000(2040)注:本規格中,頂蓋載荷主要是指橫梁支撐的上部載荷。Plywood choose GB/T 2004 Plywood The Third Part: General Technical Conditions of Ordinary Plywood of III kind of plywood. 頂蓋載荷 The top load施于橫梁的頂蓋載荷，(510kgf/m2)。 Length of crack is no more than 20% of plank. Width of crack is no more than fissure is not allowed.裂長不大于檔長10%裂寬不大于1mm，橫裂不許有Length of crack is no more than 10% of crosspiece. Width of crack is no more than 1mm. Transverse fissure is not allowed.夾 皮Bark pocket不許有 not allowed斜 紋Cross grain斜紋的傾斜度不得超過20% The inclination of the cross grain should not exceed 20%鈍 棱Wane箱面上、下口鈍棱缺角尺寸不許有，中間、兩端鈍棱缺角尺寸不大于板厚30%Under the box surface, blunt edge missing angle size is not allowed to have. Both end and middle blunt edge missing angle size is not more than 30% of veneer thickness.鈍棱缺角尺寸不大于板厚25%A blunt edge missing angle size is not more than 25% of veneer thickness.注： 所有節子缺陷，在板、檔兩端著釘范圍不得超過單板、箱檔寬度的25%，鈍棱面必須朝里。 The bending and transverse bending should not exceed 1%.Crosswise concaving should not exceed 2%.斜 紋Cross grain紋理的傾斜度不得超過20%The inclination of the texture should not exceed 20%.表2 木材的缺陷限度（箱板、箱檔）Table 2 Defects limit of wood ( boxboard, cleat)缺 陷Defect允 許 缺 陷 限 度allowed defects limit 箱 板boxboard箱 檔cleat腐 朽Decayed不允許 not allowed蟲 眼Wormhole不許有 not allowed節子Knot死 節Dead knot直徑自5mm以下不計?；九c枕木的釘接部位不得有死節。Wood moisture content is not more than 24% and other parts the moisture content of lumber is not more than 20%. 制箱木材各部位允許缺陷度見表表2，木材中各種缺陷的解釋和計算方法、斜紋的傾斜度檢量方法按GB/T 155和GB/T 4823的規定。Packaging material of transformer is given priority to with wood material which shall be under the prerequisite of the intensity of packing and to choose the appropriate tree species in unaffected areas according to the economic and environmental protection principle. Selection of main stress ponents are dahurian larch, pine, hemlock and douglas fir. The ma
公司管理相關推薦
鄂ICP備17016276號-1