出口產品運輸產品包裝標準(最終版)-wenkub.com
2025-07-11 18:36 本頁面
【正文】 加固方法詳見GB/T 7284。梁承結構如圖2所示。End plate is installed in the top of wood. Both sides have it. It has the role of supporting the stacking load.側板與端板的厚度如表8所示。Crosstie is installed on slippery wood by bolts or steel nails. Diameter of coupling bolts or steel nails is according to the stipulation in table 7.表7 枕木的安裝Table 7 Installing of crosstie枕 木 的 厚 度Thickness of crosstie mm安 裝 方 法Installation method≤60用鋼釘釘 by steel nail60~90用M10螺栓緊固 fixed by M10 bolts90~150用M12螺栓緊固 fixed by M12 bolts≥150用M16螺栓緊固 fixed by M16 bolts 底板 Baseplate底板寬度不應小于200mm，厚度按表6規定使用。Slippery wood should adopt a piece of plete log. If the length is not enough, it can be butt joint but the docking position cannot be in the center of the length. And the docking position of each slide wood should stagger.表6 底座各構件的尺寸 mmTable 6 Sizes of ponents of floor mm內裝物重 量kgWeight of builtin objects kg滑木 Slippery wood端木terminal wood（寬厚）( width * thickness)端木與滑木聯結用螺栓直徑Diameter of bolts for terminal wood and slippery wood jointingmm底板的厚度Thickness of floor箱的內長Inseam length≤尺寸 Sizes（寬X厚）( width * thickness)木板boardmm膠合板plywoodmm≤1000350090606060M10或鋼釘Or steel nail151000~50005000120120100100M121895000~100007000150150120120M162112 Terminal wood端木用螺栓或鋼釘安裝在滑木上，端木外側面距滑木端部的距離等于端木的厚度，端木的尺寸及其與滑木聯結用螺栓的直徑按表6的規定，端木的長度與內寬相同。Base is the bottom of the case on which lateral plate and end plate are installed. Its role is to support the stowage. The structure of the base as shown in picture 1. Sizes of each ponent of base are shown in table 6.圖1 底座結構Picture 1 bottom structure注：底座（或底盤、底架木）上放上內裝物后，在未進行固定加固、綁扎等或未裝側板，端板之前，不得單靠底盤進行起吊等裝卸作業。Dimensional deviation of the width and thickness of the wooden pieces is stipulated in the table 5.表5木構件的寬度與厚度的尺寸偏差（mm）Table 5 Dimensional deviation of width and thickness of timber ponents (mm)尺寸范圍 Range of sizes偏差 Deviation≤201~+220~100177。In order to prevent the builtin objects damage caused by contact with the face of the frame wooden box, filling buffer materials among them or leaving appropriate gap. Single gap is 30mm. methods of size,根據表4規定。堆碼載荷主要是指側框支撐的上部載荷。Note: All defects of knots, on both ends of plate, the pin scope shall not exceed 25% of the single board, box gear width, blunt edge surface must be inwards.膠合板選用GB/T 《膠合板 第3部分：普通膠合板通用技術條件》中規定的Ⅲ類膠合板。Any material in 1000 mm long, the number of knot is no more than 5, the diameter of biggest knot is no more than 30% of the material width ( Dead knot must be repaired.) Knot with diameter less than 5mm is not counted. Nail parts of slippery wood and crosstie can not have dead knots.腐 朽Decayed不允許 not allowed蟲 孔Wormhole不允許 not allowed裂 紋Crack裂紋長度不得超過材長的20%（寬度不足3mm的裂紋不計），不允許有貫通裂紋Length of crack is no more than 20% of material length ( crack with width less than 3mm is not counted), holethrough crack is not allowed.鈍 棱Wane鈍棱最嚴重的部分缺角寬度不得超過材寬的30%，高度不得超過材厚的三分之一A blunt edge of the most serious part of the missing angle width shall not exceed 30% of the material width. Height should not exceed one third of the material thickness.彎 曲Curve順彎、橫彎不得超過1%，翹彎不得超過2%The board color of same packing case should be consistent. It has the uniform width, flat
公司管理相關推薦
鄂ICP備17016276號-1