【正文】 ood from slippery wood end distance is equal to the thickness of terminal wood. Size of terminal wood and diameter of bolts coupling with slippery wood are according to the provisions in table 6. Crosstie主要起支撐內裝物的作用，尺寸根據包裝箱滑木位置、內裝物的重量及形狀等來決定。枕木規格應符合內裝物對包裝箱的強度要求，具體按GB/T 72841998 。It has the role of supporting builtin objects. The size is decided according to the location of packaging case slippery wood, weight and shape of builtin objects. The specifications of crosstie should be consistent with the strength of the builtin objects for packaging requirements. Specific situation is according to regulation in GB/T 72841998.枕木用螺栓或鋼釘安裝在滑木上,聯結螺栓或鋼釘?shù)闹睆桨幢?的規定。Crosstie is installed on slippery wood by bolts or steel nails. Diameter of coupling bolts or steel nails is according to the stipulation in table 7.表7 枕木的安裝Table 7 Installing of crosstie枕 木 的 厚 度Thickness of crosstie mm安 裝 方 法Installation method≤60用鋼釘釘 by steel nail60~90用M10螺栓緊固 fixed by M10 bolts90~150用M12螺栓緊固 fixed by M12 bolts≥150用M16螺栓緊固 fixed by M16 bolts 底板 Baseplate底板寬度不應小于200mm，厚度按表6規定使用。底板用鋼釘安裝在滑木上。Width of baseplate should not less than 200mm, the thickness used as the stipulation in the table 6. Baseplate is installed on slippery wood with steel nail. Side and end face plate and end plate側板裝在滑木上承受堆碼載荷,同時起通過滑木支撐貨物的作用。Lateral plate installed on the slippery wood bears stacking load and has the role of supporting goods through slippery wood.端板裝在滑木上層,兩端都有,起支撐堆碼載荷的作用。End plate is installed in the top of wood. Both sides have it. It has the role of supporting the stacking load.側板與端板的厚度如表8所示。Thickness of lateral plate and end plate is shown in table 8.表8 側板和端板的厚度mmTable 8 Thickness of lateral plate and end plate內裝物質量，weight of builtin object kg木板 board膠合板 plywood≤10001591000~5000185000~100002112 Upright and auxiliary upright側面的每根立柱都和輔助立柱、側板一起，可視為一根柱子。它們必須具有能承受作用于一根柱子上的堆碼載荷的強度，橫截面尺寸規格和計算方法按GB/。Every lateral upright with auxiliary upright and lateral plate can be regarded as a pillar. They must have the strength to bear stacking load acting on a pillar. The dimensions and the calculation method of transversal surface should according to the stipulation GB/T72841998. grillage梁承起支撐頂蓋梁的作用，在橫梁下方，由上框木用鋼釘將梁承釘在立柱上 。梁承結構如圖2所示。Its role is to support roof beam. It is below the beam. By box wood to nail grider grillage on the pillar with steel nail. The structure of grider grillage is shown in picture 2.圖2 梁承結構Picture 2 the structure of grider grillage Header頂蓋裝在側框和端框上起支撐頂蓋載荷的作用，作為橫梁、梁撐，固定鋼纜的加強材，用釘子釘在側框和端框上。頂蓋結構如圖3。Header is installed on the side frame and end frame to support the roof load. As beam, beam support, anchor cable reinforcement, to use a nail on the side frame and end frame. The structure of header is shown in picture 3.圖3 頂蓋結構Picture 3 the structure of header 橫梁 Beam橫梁支撐頂蓋載荷，同時承受鋼纜起吊時所產生的壓縮作用，橫梁中心間隔原則上不大于600mm，如果上框木正好是起吊繩索通過的部位，或當木箱較寬時，應對上框木進行加強。加固方法詳見GB/T 7284。Beam supports roof load, at the same time bear the pression function of the produced during the wirerope hoist. The beam center spacing, in principle, is not more than 600 mm. If upper ledge wood is just the part lifting rope go through, or when the case is wider, we must strength upper ledge wood. Strengthening method is shown in GB/T 728