出口產品運輸產品包裝標準(最終版)(參考版)
2025-07-17 18:36本頁面
【正文】 Beam supports roof load, at the same time bear the pression function of the produced during the wirerope hoist. The beam center spacing, in principle, is not more than 600 mm. If upper ledge wood is just the part lifting rope go through, or when the case is wider, we must strength upper ledge wood. Strengthening method is shown in GB/T 7284.。Header is installed on the side frame and end frame to support the roof load. As beam, beam support, anchor cable reinforcement, to use a nail on the side frame and end frame. The structure of header is shown in picture 3.圖3 頂蓋結構Picture 3 the structure of header 橫梁 Beam橫梁支撐頂蓋載荷，同時承受鋼纜起吊時所產生的壓縮作用，橫梁中心間隔原則上不大于600mm，如果上框木正好是起吊繩索通過的部位，或當木箱較寬時，應對上框木進行加強。Its role is to support roof beam. It is below the beam. By box wood to nail grider grillage on the pillar with steel nail. The structure of grider grillage is shown in picture 2.圖2 梁承結構Picture 2 the structure of grider grillage Header頂蓋裝在側框和端框上起支撐頂蓋載荷的作用，作為橫梁、梁撐，固定鋼纜的加強材，用釘子釘在側框和端框上。Every lateral upright with auxiliary upright and lateral plate can be regarded as a pillar. They must have the strength to bear stacking load acting on a pillar. The dimensions and the calculation method of transversal surface should according to the stipulation GB/T72841998. grillage梁承起支撐頂蓋梁的作用，在橫梁下方，由上框木用鋼釘將梁承釘在立柱上 。Thickness of lateral plate and end plate is shown in table 8.表8 側板和端板的厚度mmTable 8 Thickness of lateral plate and end plate內裝物質量，weight of builtin object kg木板 board膠合板 plywood≤10001591000~5000185000~100002112 Upright and auxiliary upright側面的每根立柱都和輔助立柱、側板一起，可視為一根柱子。Lateral plate installed on the slippery wood bears stacking load and has the role of supporting goods through slippery wood.端板裝在滑木上層,兩端都有,起支撐堆碼載荷的作用。底板用鋼釘安裝在滑木上。It has the role of supporting builtin objects. The size is decided according to the location of packaging case slippery wood, weight and shape of builtin objects. The specifications of crosstie should be consistent with the strength of the builtin objects for packaging requirements. Specific situation is according to regulation in GB/T 72841998.枕木用螺栓或鋼釘安裝在滑木上,聯結螺栓或鋼釘?shù)闹睆桨幢?的規定。Terminal wood is installed on slippery wood with bolts and steel nails. The lateral aspect of terminal wood from slippery wood end distance is equal to the thickness of terminal wood. Size of terminal wood and diameter of bolts coupling with slippery wood are according to the provisions in table 6. Crosstie主要起支撐內裝物的作用，尺寸根據包裝箱滑木位置、內裝物的重量及形狀等來決定。The center interval of the slippery wood is generally not more than 1200 mm. When need to use the forklift into the fork loading and unloading crosswise, the center interval of the slippery wood is generally not more than 1000 mm (weight of builtin objects below1500 kg, should not be greater than 800 mm). In excess of the prescribed intervals, we should increase slippery wood with the same cross section. ，若長度不夠時，可以對接，但對接的位置不能在長度的中心處，而且各滑木的對接位置應錯開。Note：Builtin objects put on base (or chassis, timber underframe), without fixed reinforcement, binding, etc or without installing lateral plate and end plate, chassis would not be allowed to lifting handling operation, etc alone. wood，但對底板兼枕木的形式，若內裝物底座用螺栓固定在滑木上，限于螺栓孔位置，滑木的位置可以適當偏移。底座各構件尺寸見表6。2≥100177。dimension長(L)寬(W)高(H)端支柱的內面間距離The distanc
公司管理相關推薦
鄂ICP備17016276號-1