基于單片機的智能晾衣架控制系統的設計與實現外文文獻原稿和譯文-文庫吧資料
2025-06-24 18:47本頁面
【正文】 . In this mode, P0 has internal pullups. Port 0 also receives the code bytes during Flash programming and outputs the code bytes during program verification. External pullups are required during program verification.Port 1 is an 8bit bidirectional I/O port with internal pullups. The Port 1 output buffers can sink/source four TTL inputs. When 1s are written to Port 1 pins, they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source current (IIL) because of the internal pullups. Port 1 also receives the loworder address bytes during Flash programming and verification.Port PinAlternate FunctionsMOSI (used for InSystem Programming)MOSO (used for InSystem Programming) SCK(used for InSystem Programming)Port 2 is an 8bit bidirectional I/O port with internal pullups. The Port 2 output buffers can sink/source four TTL inputs. When 1s are written to Port 2 pins, they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (IIL) because of the internal 2 emits the highorder address byte during fetches from external program memory and during accesses to external data memory that use 16bit addresses (MOVX DPTR). In this application, Port 2 uses strong internal pullups when emitting 1s. During accesses to external data memory that use 8bit addresses (MOVX RI), Port 2 emits the contents of the P2 Special Function Register. Port 2 also receives the highorder address bits and some control signals during Flash programming and verification.Port 3 is an 8bit bidirectional I/O port with internal pullups. The Port 3 output buffers can sink/source four TTL inputs. When 1s are written to Port 3 pins, they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL) because of the pullups. Port 3 receives some control signals for Flash programming and verification. Port 3 also serves the functions of various special features of the AT89S51, as shown in the following table.Port PinAlternate FunctionsRXD(serial input port)TXD(serial output port)INT0(external interrupt 0)INT1(external interrupt 1)T0(timer 0 external input)T1(timer 1 external input)WR(external data memory write strobe)RD(external data memory read strobe)3 Special Function RegistersA map of the onchip memory area called the Special Function Register (SFR) space is shown in Table 31. Table 31. AT89S51 SFR Map and Reset Values0F8H 0FFH 0F0H B 00000000 0F7H 0E8H 0EFH 0E0H ACC 00000000 0E7H 0D8H 0DFH 0D0H PSW 00000000 0D7H 0C8H 0CFH 0C0H 0C7H 0B8H IP XX000000 0BFH 0B0H P3 11111111 0B7H 0A8H IE 0X000000 0AFH 0A0H P2 11111111 AUXR1 XXXXXXX0 WDTRST XXXXXXXX 0A7H 98H SCON 00000000 SBUF XXXXXXXX 9FH 90H P1 11111111 97H 88H TCON 00000000 TMOD 00000000 TL0 00000000 TL1 00000000 TH0 00000000 TH1 00000000 AUXR XXX00XX 8FH 80H P0 11111111 SP 00000111 DP0L 00000000 DP0H 00000000 DP1L 00000000 DP1H 00000000 PCON 0XXX0000 87H Note that not all of the addresses are occupied, and unoccupied addresses may not be implemented on the chip. Read accesses to these addresses will in general return random data, and write accesses will have an indeterminate effect. User software should not write 1s to these unlisted locations, since they may be used in future products to invoke new features. In that case, the reset or inactive values of the new bits will always be 0. Interrupt Registers: The individual interrupt enable bits are in the IE register. Two priorities can be set for each of the five interrupt sources in the IP register.Table 32. AUXR:Auxiliary Regist
高考資料相關推薦
鄂ICP備17016276號-1