【正文】 sion test電源轉換試驗Cut off emergency switchboard one by one, whether the switchboard has been transferred into emergency working state within 5s.逐個切斷應急配電盤，該配電盤是否在5s內轉入應急工作狀態。5Check of identification lamp of emergency fire fighting應急消防標志燈檢查Check whether installation positions of all emergency fire identification lamps and arrow indication directions of mark information ply with actual evacuation direction or not.檢查所有應急消防標志燈安裝位置和標志信息上的箭頭指示方向是否與實體疏散方向相符。3Loop check回路檢查Connect and open single loop, test situation of power on and munication of every loop.分次逐一連接開通單條回路，測試每個回路的通電、通訊情況。調試前應編制調試程序，并按調試程序工作。2）Commissioning contents are shown in the table .2）。（6）Commissioning of automatic fire alarm system （6）火災自動報警系統調試1）System overview1）系統概述Automatic fire alarm system of the project is centralized alarm system. The system is posed of the following parts: automatic fire alarm system, linkage mand control system, gas fire extinguishing control system, elevator monitoring system, fire emergency broadcasting system, telephone system special used for firefighting control, electrical fire monitoring system, firefighting power monitoring system, firefighting door monitoring system, emergency lighting and firefighting system grounding.本項目火災自動報警系統為集中報警系統。Electromagnetic pulse prevention (overvoltage protection)防電磁脈沖（過電壓保護）2Grounding system接地系統Medium voltage and low voltage power supply grounding system中壓、低壓供電接地系統Neutral ground system of generator發電機中性點接地系統Grounding system of tele and puter equipment電信及計算機設備接地系統Weak current system grounding弱電系統接地3Equipotential connection等電位連接Various transformer substation room, auxiliary room of equipment, metal pipe and metal matter各變配電房、設備機房輔助用房、金屬管道及金屬物（1）Calibration of wire resistance。Table Commissioning of grounding resistance and equipotential grounding system 接地電阻及等電位接地系統調試No.序號Name of system系統名稱Type種類Commissioning content調試內容1Lightning protection system防雷系統Flank thunder prevention, direct lightning prevention, inductive thunder prevention防側擊雷、防直擊雷、防感應雷（1）Test of grounding resistance.（1）接地電阻測試。4Commissioning records調試記錄Make missioning records when missioning.在調試的同時作好調試記錄。 and then supply power for power /lighting main line cables.（1）所有分段分區域分系統調試完后，進行總體送電運行調試，先切斷各區的動力/照明控制盤開關；然后對動力/照明主干線電纜送電。（2）All power/lighting switchboards adopt temporary power supply to conduct closing and opening test for main switch and separating switch of the switchboard, check whether closing and opening of all switchboard switches are normal or not.（2）所有動力/照明配電盤，采用臨時電源對配電盤總開關、分開關進行分合閘試驗，檢查各配電盤開關分合是否正常。（2）Recheck whether the test of ponents of all power/lighting accessories such as busbar, cable, motor and lamps is qualified or not and whether its wiring is correct or not.（2）再檢查各動力/照明配件組成部分如：母線、電纜、電動機、燈具等，是否測試合格及接線準確。（3）Commissioning of power/lighting system（3）動力/照明系統的調試Commissioning contents are shown in the table .。②確認系統中所有盤面、柜面、板面的分合閘開關、儲能開關、電源切換開關、控制開關、電源開關處于分閘位置；③It shall conduct simulation test of interlocking and double switching in accordance with design requirements if the system is a electric transformer and distribution system which is supplying power for two circuits, operating in sections and backup of each other.③對于系統為兩路供電、分段運行、互為備用的變配電系統，應按其設計要求進行互鎖互投的模擬試驗。 if any damage, it shall be supplemented or replaced with electrical elements with the same model in time。3）System test:3）系統試驗：①Check whether indicating and monitoring elements, operation amp。⑤所有配電柜中的臨時電源應全部拆除，并恢復其原設計線路；⑥Insulation of all equipment and circuits plies with requirements of the specification。④檢查所有負荷開關柜的聯鎖、互動機構是否轉動靈活、可靠；⑤Temporary power supply in all distribution boxes shall be dismantled。 whether there is not blockage phenomenon or not。①檢查母線、互感器、避雷器、電容器、變壓器等設備元件的連接螺栓是否按要配齊上緊；②Check whether the grounding of auxiliary equipment such as low voltage cabinet plies with design requirements or not。 System missioning 系統調試1. Commissioning of electrical system work電氣系統工程的調試（1）Commissioning process of electrical system work（1）電氣系統工程調試流程Figure Commissioning process of electrical system work 電氣系統工程調試流程（2）Commissioning contents of electric transformation and distribution system （2）變配電系統調試內容：1）Sanitation clearing: clear sundries on site away, clean all equipment.1）衛生清理：清理現場雜物，將所有設備打掃干凈。風機啟動運轉平穩后，測量風機起動電流，運轉電流、振動、轉速、噪聲及軸承溫度。 check whether rotating direction is consistent with the direction marked on the enclosure or not. After the fan operates stably, measure starting current, operation current, vibration, revolving speed, noise and bearing temperature of the fan。（8）Fan: rotate the impeller by hands, observe whether there are jamming and collision phenomenon or not。 if it is normal through check, the motor shall be operated for two hours with no load。 check the correctness of stator winding and its connection。 whether the connection of wire, cable, guide line and terminal is solid or not.2）用萬用表檢查柜箱內空氣開關，其開關分、合閘是否正常；檢查一次、二次線路接線符合設計要求；電線、電纜、導線和端子連接是否緊固；3）Shall calibrate precision of amperemeter or voltmeter on the switchboard.3）應對配電盤上電流表或電壓表進行精度校驗。1）采用1000V或500V兆歐表對箱內供電回路開關，一次、二次線路進行絕緣檢查，絕緣電阻符合規范要求；2）Check air switch in the cabinet by using universal meter, whether its switching off and switching on are normal or not。 secondary circuit in the power supply loop in the cabinet by using 1000V or 500V tramegger。（5）SPD: missioning as per technical specification of the manufacturer.（5）避雷器：按生產廠家技術說明進行調試。 2）check wiring group and polarity。（3）Meter: conduct precision calibration for instrument on the plate cabinet by using standard meter.（3）表：用標準表對盤柜上的儀表進行精度校驗。 2）breakingclosing test。 6）cross interconnection system test.（1）電力電纜：1）測量絕緣電阻；2）直流耐壓試驗及泄漏電流測量；3）交流耐壓試驗；4）測量金屬屏蔽層電阻和導體電阻比；5）檢查電纜線路兩端的相位；6）交叉互聯系統試驗。 4）measure ratio of resistance of metallic shield layer and conductor resistance。 2）DC voltage withstand test and measureme