【正文】 For the real leather/mesh/synthetic material, first clean with water. 如擦不干淨 ,真皮 /人造皮用去漬水再清潔 ,網布可用清水 +醋再清潔 .注意不要用去漬水清洗網布 ,以免網布脫層 . If still not dirty after clean with water, need clean with detergent again for the real leather/ synthetic, and do with water + vinegar . Note: don’ t clean mesh with detergent to avoid mesh from delaminating. , Make sure to clean pletely. ,通常距鞋墊商標 5mm處 .再塞鞋墊 . Attach the in sock label on the indicated position of in sock ,monly distance 5mm from the in sock logo. Then insert in sock. 清潔鞋面 : 貼鞋墊標塞鞋墊 塞紙團或鞋撐 Coordinate Lace Inserter wrapping paper or stuffer 1,整理鞋帶 ,使助帶口寬度正確 ,且鞋帶外露長度正確 . Coordinate shoe lace to make sure the eyelet stay width the shoe lace length from the last eyelet hole to lace tip correct . .依鞋子的型狀 ,如拔楦後鞋面易塌陷的需塞鞋撐 . Insert the wrapping paper on the forefoot portion. According to the shape of shoe , if the upper easily collapse after delast, need insert the stuffer . 整理鞋帶 塞鞋頭紙 烘線 CLEAN O/S HOT THREAD EDGE 1,用 633BF+水把大底清洗干淨 . Clean O/S with 633BF+ water. . Hot the exposed thread edge. 清洗大底 烘線頭 1,核對成品鞋的 SIZE. Check the finished size. ,準備相應 SIZE內盒 ,并貼上相應的內盒標 ,需貼在規定的位置 . Prepare the shoe box plate of corresponding size to fold. Then attach the corresponding shoe box label on the indicated position. 4. 將鞋子用包裝紙包好 ,再裝入內盒 . Pack the shoe with wrapping paper then put into the corresponding shoe box. 包裝 FOLD SHOE BOX PACK ,SIZE要與成品鞋一致 SIZE 演講完畢，謝謝觀看！ 。時間 :8分鐘 . Put the finished shoe on the conveyer belt through the cool trunk to keep the shape of shoe. Set the cool trunk with the temperature 05 。上下壓機壓力 35KG/CM2 ,時間 810秒 . Adjust the proper pressure time. Common for universal pressing machine pressure :40KG/CM2 ,time : 15 seconds。 . The marking for cement should not be exposed not be over . ﹐ 放在鋼板上檢查大底是否平穩。如鞋面是網布或人造皮 ,需刷一次膠用 116NN+35E%1000. For the leather upper including suede, no need first cement。底部配件在烘箱上層 ,烘箱溫度 5055度 ,時間均為 2分鐘 . Put the lasted upper on top layer of oven and set the temperature 7080。EVA with UV light. Primer Shanks with 111YCN+2%RFE. ,面皮用 UE9SF+57%CL12處理 ,人造皮用 111YCN+2%E1000,網布不需藥水處理 . Primer the suede and leather with UE9SF+57%CL12, for synthetic use 111YCN+2%E1000 ,for mesh no need primer. ﹐ 藥水不可太少或過量 ﹐ 不可有外溢現象。 light time 1012sec for both color. Shank用 111YCN+2%RFE藥水處理 Primer O/S: White rubber with 1016A+1%B。varied color rubber do with 1016A+23%。雜色用 1016A+23%B粉 。壓力均為 35公斤 ,時間 10秒 . Set the proper parameter of machine. For the suede version, the temperature of the iron plate is indoor。 After the allowance must be smooth upper must fit the last on the medial lateral portion . 鳥嘴鉗 Pincer 腰幫機 Side lasting machine 1,設定 后幫機器正確參數 ,壓力 35公斤 ,時間 :5秒 ,掃刀溫度 :室內自然溫度 . Set the proper parameter of heel lasting machine with pressure 35 kilo, time 5 sec and temperature as the indoor’ s. 2. 依訂單楦頭及後跟定型模更換掃刀 (圓角楦頭用圓掃刀 ). Change to the proper wiper of heel lasting machine as per the correct last heel molding mold. (For round angle last, use the round shape wiper. :相同號碼之后跟高度要一致 . Need check the heel height to make sure it’ s consistence for one pair after pressing . ,進入下一流程 .