【正文】 is permissible.TypeOrder no.RatedmotorpowerkWRatedoutputcurrentAmax. output current A for 30sOutput power kVA400V 50 Hz 480V 60 HzMainscurrentAPowerlossW8601 E1308602 E1408603 E1608604 E1808605 E2008606 E2408607 E2758608 E3508609 E4208610 E6008611 E7408612 E9008613 E10508614 E10508615 E1270MM,NOJiucold16 Applications with high overload,peak torque up to 170% of the rated motor torque For applications which require a standardoverload behaviour of an inverter (. generalmechanical engineering, hoists, travelling drives,calenders). The inverter provides 150% of the rated torque fora maximum of 30s.In the event of cyclic overload, the ratio of overloadtime and cycle time must not exceed . For this application, the monitoring of the outputcurrent is set to operation with increased powerusing the codes C119 and C120 (see page 97). Please note that a maximum ambient temperature of 45176。C is permissible.TypeOrder no.RatedmotorpowerkWRatedoutputcurrentAmax. output current A for 30sOutput power kVA400V 50 Hz 480V 60 HzMainscurrentAPowerlossW8601 E1408602 E1558603 E1808604 E2108605 E2358606 E2908607 E3408608 E4408609 E5608610 E6708611 E7758612 E9608613 E11758614 E13758615 E1675FMannmg17 Application with medium overload,peak torque up to 135% of the rated motor torque For applications where only small starting andoverload torques are necessary (. ventilators,pumps). The inverter provides 110% of the rated torque fora maximum of 30s.In the event of cyclic overload, the ratio of overloadtime and cycle time must not exceed . For this application, the monitoring of the outputcurrent is set to operation with maximum powerusing the codes C119 and C120 (see page 97) Please note that a maximum ambient temperature of 40176。C is permissible.TypeOrder no.RatedmotorpowerkWRatedoutputcurrentAmax. output current A for 30sOutput power kVA400V 50 Hz 480V 60 HzMainscurrentAPowerlossW8601 E1558602 E1758603 E2058604 E2358605 E8606 E3408607 E8608 E5508609 E7108610 E7608611 E8612 E11108613 E13208614*****16401640*8615 E一一一一一一一* These data are valid for a maximum ambient temperature of 30176。C.6iucold184 Installation Mechanical installation? These frequency inverters must only be used as builtin units.? Install the inverter vertically with the terminal strips at the bottom.? Allow a free space of 100 mm at the top and bottom. For the units 8612 ... 8615 this free space is also required at both sides.Ensure unimpeded ventilation of cooling air.? If the cooling air contains pollutants (dust, flakes, grease, aggressive gases), which may impair the inverter functions, suitable preventive measures must be taken, . separate air duct, installation of a fiter, regular cleaning, etc.? If the inverters are permanently subjected to vibration or shaking, shock absorbers may be necessary.plcunnlng19 Electrical installation? The drive controllers are equipped with electrostatically endangered ponents. The service and maintenance personnel must be electrostatically discharged before working at the units.They can discharge by touching the PE fastening screw or another earthed metallic surface in the control cabinet.? All control inputs and outputs of the inverter are mainsisolated. The mains isolation has a basic insulation. The control inputs and outputs must be integrated into another level of protection against direct contact.Use insulated operating elements, connect the mechanical screwed joint of the setvalue potentiometer to PE (assembly kit).? Not used control inputs and outputs should be covered with plugs or protective covers which are supplied together with the unit.? When using currentoperated protective units:The controllers are equipped with an internal mains rectifier. As result, a DC fault current may prevent the tripping of the currentoperated protective device after a shortcircuit to frame.Therefore, additional measures as protective multiple earthing or universalcurrent sensitive currentoperated . are required. When dimensioning the tripping current of currentoperated . it must be observed that there are capacitive leakage currents between cable screens and RFI filters during operation. These currents may result in false tripping of the currentoperated .? The regulation about the min. crosssection of PE cables must be observed. The crosssection of the PE cable must be at least as large as the crosssection of the power connections.? In the event of condensation, only connect the inverter to the mains when visible moisture has evaporated.? Before switching on the inverter for the first time check whether there is an earth fault at the output side, if this is the case, clear the earth fault. Earth faults which occur during operation are detected, the inverter is then switched off and the message OC1 is set.? Frequent mains switching may overload the internal switchon current limitation. For repeated mains connection, the inverter must not switched mo