八路搶答器說明書-資料下載頁
2025-08-02 23:44本頁面
【正文】 ,TRUE6 JNB ,TRUE7 JNB ,TRUE8 AJMP RECOUNTQUIT: CLR OK 。如果按下了停止鍵執行的程序 CLR RING AJMP START。======正常搶答處理程序======TRUE1: ACALL BARK 。調用發聲程序 MOV A,R2 MOV R6,A 。搶答時間R2送R6 MOV R3,01H CLR OK 。因?yàn)榇痤}的計時不再查詢搶答,所以就鎖了搶答 AJMP COUNT 。調用倒計時子程序TRUE2: ACALL BARK 。調用發聲程序 MOV A,R2 。搶答時間R2送R6 MOV R6,A MOV R3,02H CLR OK AJMP COUNT 。調用倒計時子程序TRUE3: ACALL BARK 。調用倒計時子程序 MOV A,R2 。搶答時間R2送R6 MOV R6,A MOV R3,03H CLR OK AJMP COUNT 。調用倒計時子程序TRUE4: ACALL BARK 。調用發聲程序 MOV A,R2 。搶答時間R2送R6 MOV R6,A MOV R3,04H CLR OK AJMP COUNT 。調用發聲程序TRUE5: ACALL BARK 。調用發聲程序 MOV A,R2 。搶答時間R2送R6 MOV R6,A MOV R3,05H CLR OK AJMP COUNT 。調用倒計時子程序TRUE6: ACALL BARK 。調用發聲程序 MOV A,R2 。搶答時間R2送R6 MOV R6,A MOV R3,06H CLR OK AJMP COUNT 。調用倒計時子程序TRUE7: ACALL BARK 。調用發聲程序 MOV A,R2 。搶答時間R2送R6 MOV R6,A MOV R3,07H CLR OK AJMP COUNT 。調用倒計時子程序TRUE8: ACALL BARK 。調用發聲程序 MOV A,R2 。搶答時間R2送R6 MOV R6,A MOV R3,08H CLR OK AJMP COUNT 。調用倒計時子程序。======延時6357個機器周期(去抖動用到)======DELAY: MOV 32H,12HLOOP: MOV 33H,0AFHLOOP1: DJNZ 33H,LOOP1 DJNZ 32H,LOOP RET。 =====延時4236個機器周期(顯示用到)=====DELAY2: MOV 32H,43HLOOP3: MOV 33H,1EH MOV A,R7 。每隔60~70個機器周期讀一次P1口,全為1時為無效數據,繼續讀,有一個不為1時,轉到正常搶答處理 JNZ AAAA1 。沒讀到有效數據時繼續轉到AAAA1LOOP2: DJNZ 33H,LOOP2 DJNZ 32H,LOOP3 RET。======讀搶答鍵數據口程序====== 。由于在讀搶答數據口的時候，單片機首先進入倒計時程序，再調用顯示程序，最后才檢測按鍵口 。然而在檢測按鍵口時動態掃描要調用三次(4ms),. 。AAAA1: MOV A,P1 CJNE A,0FFH,AA1 。當不全為1時的數據為有效數據AA0: MOV 36H,A 。將有效數據送到36H暫存 AJMP LOOP2AA1: DEC R7 AJMP AA0。======發聲程序======BARK: SETB RING ACALL DELAY ACALL DELAY CLR RING RET。======T0溢出中斷(響鈴程序)=====T0INT: MOV TH0,0ECH MOV TL0,0FFH JNB RING,OUT CPL 。RING。OUT: RETI。======T1溢出中斷(計時程序)======T1INT: MOV TH1,3CH MOV TL1,0B0H INC R0 RETI END附2：參考文獻【1】汪貴平 李登峰 等 新編單片機原理及應用【M】.北京：機械工業出版社，2009.【2】【2】【3】查電子元器件資料：：//【4】萬方數據： 18
規章制度相關推薦
鄂ICP備17016276號-1