三防漆涂覆工藝規范a00中英文-資料下載頁
2024-11-08 13:17本頁面
【導讀】熱沖擊、防霉、防濕，還應具有柔韌性和阻燃性。多余的三防漆則流回容器，通過泵送到高位槽中循環使用。是一種較少采用的三防漆涂覆方法。我司根據產品難易度，目前采用刷涂法和噴涂法兩種，操作流程為：PCB清潔/烘烤——配置涂覆劑——遮掩——涂覆——檢驗——烘干——檢驗——修補——轉下工序。確認涂覆工藝包括涂覆方式、烘干溫度、烘干時間、工具、量具等。
【正文】 cording to customer requirements 不可涂的元件及不良現象詳見附件1。unsuitable ponents and defect is in Annex 1. 操作注意事項：Operating note 操作時要戴好口罩或防毒面具、橡膠手套、化學防護眼鏡等防護器具，以免傷害到身體；The operator should wear masks or gas masks, rubber gloves, chemical safety goggles and other protective equipment, to avoid harming to the body。 操作間禁止吸煙，工作前不要飲用酒精性飲料；飲水或飲食前要清潔其手。Do not smoking in the operating room, do not drink alcohol before work。 Wash hands before drinking or eating 操作時不要將PCBA重疊放置，PCB板要水平放置；Operation Do not allow overlap the PCBA together, Put the PCB A in level . 作業完畢后，及時清洗用過的器皿，整理、擦拭工具和設備，并將裝有三防漆的容器蓋嚴；When the job is finished, clean containers, clean tools and equipment, and airproof the container . 禁止把使用剩余的三防漆倒回原存儲容器內，要分開密閉保存；Prohibit putting the remaining coating back into the original storage container . 不慎濺入眼晴應立即翻開上下眼瞼，用流動清水或生理鹽水沖洗干凈，然后就醫處理； Accidentally splashed into the eyes should immediately open the upper eyelids, rinse with running water or saline, and medical treatment。 刷涂時如感覺不適，應迅速離開作業現場至空氣新鮮處，呼吸困難時給予輸氧，然后就醫處理； if you feel unwell, you should quickly leave the job to fresh air, give oxygen breathing, then let a doctor deal with。參考文件: References: IPCA610E JSTD001 IPCCC8307. 應用表單: Application Forms 《三防漆膜厚測試記錄》Caoting thickness test records 《涂覆機保養記錄表》Coating machine maintenance record sheet8．流程圖：flow chart；參考文件《BOM》《ECN》《產品作業指導書》《PCBA涂覆工藝控制規范》填寫《生產日?qǐng)?bào)表》《QC日?qǐng)?bào)表》《涂料配比確認表》《涂覆機保養記錄表》OKNG開始sstartPCBA清潔PCBA烘烤roasting外觀檢查包 裝ppackingOK涂料配比固化修補mendNGNG涂覆coating涂覆外觀檢查去遮掩裝載具、遮掩OK9．附件：Attachment 9．1 不良現象說明：Undesirable phenomena described厚度不均勻氣泡圖1 刷涂后有氣泡，厚度不均勻 bubbles and uneven thckness 圖2 雙排插針沾有三防漆needles stain coating元件腳發白 圖3 板面有手指紋 finger prints 圖4 板面有元件腳及發白現象white phenonenon圖5 有波紋rippled 圖6 板面元件半潤濕semi wetting 圖7表面未干 surface not dry 圖8表面模糊surface blur9．2 不良現象說明： 厚度均勻(even thickness)?。希恕 『穸忍?thin coating) ＮＧ 軌跡均勻(uniform texture)?。希恕 ≤壽E飛濺(splash)?。危荅ven application涂覆均勻?。希恕 ⊥扛灿袟l紋(stripe application) ＮＧ編制審核批準
黨政相關相關推薦
鄂ICP備17016276號-1