單片機智能小車畢業論文中英文資料外文翻譯外文文獻-資料下載頁
2025-08-24 19:35本頁面
【導讀】L9110芯片和LM324比較器等。本設計采用AT89C51單片機作為智能小車核心控制器。駛過程中保持直線運動且不會脫離蹺蹺。動車的智能控制。這種方案能實現對電動車的運動狀態進行實時控。制，控制，靈活可靠，精度高，可滿足對系統的各項要求。器，簡稱PWM變換器。由于PWM調速系統的開關頻率較高，僅靠。連續，系統的低速運行平穩，調速范圍較寬，可達1：10000左右。同樣由于開關頻率高，若與快速響應的電機相配合，系統可以獲得很寬的頻帶，因此快速響應性能好，動態抗擾能力強。的發展方向，本設計采用了H型單極型可逆PWM變換器進行調速。由于黑線和白紙對光線的反射系數不同可根據接收到的。在小車行駛過程中不斷地向地面發射紅外光，當紅外。光遇到白色地面時發生漫發射，反射光被裝在小車上的接收管接收；當兩個傳感器同時檢測到光時，直線前進。則向右糾正方向。整機可靠性提高。電機驅動采用片集成電機驅動芯片L298N。轉及停止行駛的目的。
【正文】 voltage signal, it could be processor receives and processing. 2. 4 remote control module design This module will launch end USES high sensitive H L 5000 type universal television remote control, the receiver using receive frequency for 38kH z39。s receiving head 1838, this module and the single chip puter interface is very convenient. In addition, for the red outside meet after harvest of plait code letter number, the department tasseled set when shipped with project of AT89C52 single chip microputer external interruption to receive, signal the falling edge of trigger external interruption. In order to recognize a plete key signal, must for each coding pulse width were measured with discriminant receives the pulse is! 0 still! 1 ?, the microcontroller timer/counter to measuring pulse width. Timer/counter except ?points than can be set, from except 2 to except 2048, measurable pulse width can reach 500m s. This paper set except points for 12, namely than 12 points frequency, because the external clock is about 12MH z, clock cycle for 1 s, so the timer/counter for 1 per timing once s. 2. 5 alarm module design Alarm module core chip 110 IC, can choose application in automobile, motorcycle, alarms, personal riot device, door magic alarm device and etc. 3. System software design This system software modular structure, the main program, initial antifuzzy procedures, interrupt subroutines, delay subroutines, buttons pronunciation subroutines, buttons scanning subroutines constitutes. 3. 1 tracing subroutines design Tracing module is designed by the left right photoelectric sensor output terminal receiving monolithic machine respectively, P 22 and P23 tube feet, then through the microcontroller programming, produce PWM control signal, through L 298 control motor speed, let the car to move forward, left turn, turn right and stop driving purpose. 3. 2 avoid barrier of programming Obstacle avoidance module is designed by the infrared reflection sensor module around the output terminal receiving MCU respectively P20 and P21 tube feet, then through the microcontroller programming, produce PWM control signal, through L298 control motor speed, let the car to move forward, left turn, turn right and stop driving purpose. 3. 3 remote subroutines design Remote control module is designed by the infrared sensor 1838 an output terminal of the receiving MCU P32 tube feet, then use allpurpose remote control on the remote control, then let microcontroller decoding, produce PWM control signal, through L298 control motor speed, let the car to move forward, left turn, turn right and stop driving purpose. 4 . Summary Adopts singlechip, using photoelectric sensor and infrared reflection sensor was designed as a detection system, can realize automatic homing line to walk, automatic obstacle avoidance, alarm and remote control functions such as intelligent car. This design is the obvious advantages of simple circuit, reliability, low cost, and very easy to function of further perfecting and expansion
環評公示相關推薦
鄂ICP備17016276號-1