【正文】 CE ON CARBON JUMPER MUST BE LESS THAN 177。50 g / cm2 4) FREQUENCY ： 2 HITS / SEC. 5) TOTAL TIMES ： 1,500,000 HITS. VARIANCE OF RESISTANCE AFTER TESTING MUST BE LESS THAN 177。15) MINS. VARIANCE OF RESISTANCE ON CARBON JUMPER MUST BE LESS THAN 177。D RING MIN. ㎜ D D D C C C B A B B B A A A A A A︰ MIN. ㎜ B︰ MIN. ㎜ B B B B 敬鵬 (蘇州 )電子有限公司 ACP. ELECTRONICS CO., LTD. F:\EN\002 19 GAP BETWEEN THE CARBON CONDUCTOR AND COPPER CONDUCTOR S≧ ㎜ PAD關係尺寸 GAP BETWEEN THE CARBON CONDUCTOR AND COPPER PAD S:≧ ㎜ PAD與防焊圈關係尺寸 RELATIVE SIZE FOR COPPER PAD OF THE CARBON JOINTED POINT AND SOLDER RESIST ANNULAR RING S S 防焊圈大於銅 PAD ㎜ SOLDER RESIST RING＞ COPPER PAD ㎜ SOLDER RESIST RING COPPER LAND 敬鵬 (蘇州 )電子有限公司 ACP. ELECTRONICS CO., LTD. F:\EN\002 20 WIDTH OF UNDERCOAT AND OVERCOAT ,製作成如下圖 IF OVER/UNDER COATS ARE TO BE AS FIG. A, IT MUST BE COMBINED AS： ㎜ 以上 ON THE CONJUNCTION, THE OVERLAP MUST BE MORE THAN ㎜ 、碳墨產品信賴性試驗 C B A CARBON COPPER B A OVER/UNDER COAT CARBON CONDUCTOR A－ B≧ ㎜ AB ≧ ㎜ C ≧ ㎜ 敬鵬 (蘇州 )電子有限公司 ACP. ELECTRONICS CO., LTD. F:\EN\002 21 THE RELIABILITY TEST OF CARBON PRODUCT 試驗項目 TEST ITEM 試驗條件 TEST CONDITION 規 格 SPECIFICATION 一 耐濕性試驗 HUMIDITY RESISTANCE TEST (60177。 VCUT 距板邊尺寸Ｍｉｎ：５㎜ 。 ※除殘厚管制外，板厚 ㎜， VCUT 深度須≧ ㎜。 不同材質之殘厚規格 THE MATERIAL REMAINING SPECIFICATION 板厚 材質 ０．８ １．０ １．２ １．６ PAPER 177。 TOLERANCE TO THE BOARD EDGE OF FIDUCIAL MARK 177。 ４、其它印刷工程及電鍍 ３、文字印刷 ５、開模及沖床工程 敬鵬 (蘇州 )電子有限公司 ACP. ELECTRONICS CO., LTD. F:\EN\002 7 外型尺寸公差： 177。 ㎜。 銅箔導體距板邊Ｍｉｎ：０．３㎜ 。 Min. EDGE TO CONDUCTOR： ㎜。 防焊隔線最小寬度 Min. SOLDER RESIST LINE WIDTH BETWEEN CONDUCTORS 銅箔厚度 THE THICKNESS OF COPPER 隔線最小寬度 Min. LINE WIDTH ３５μ m Ｍｉｎ ０．２㎜ ７０μ m Ｍｉｎ ０．３㎜ 防焊隔線導體間距 GAP BETWEEN CONDUCTORS 銅箔厚度 THE THICKNESS OF COPPER 導體最小間距 Min. GAP REQUIREMENT ３５μ m Ｍｉｎ ０．５㎜ ７０μ m Ｍｉｎ ０．６㎜ 大銅箔內孔之防焊圈尺寸︰Ｍｉｎ０．５㎜ THE MINIMUM REQUIREMENT OF THE RING BETWEEN SOLDER RESIST AND HOLE IN THE GROUND IS ㎜ . Ground A︰ S/M 圈 B︰ HOLE R 敬鵬 (蘇州 )電子有限公司 ACP. ELECTRONICS CO., LTD. F:\EN\002 6 LEGEND amp。０．１㎜ 。 ㎜。 177。 板厚 ㎜， VCUT 深度須≧ ㎜。 EDGE OF BOARD TO VCUT Min： 5 ㎜。2)℃ 95%.(500177。 50％ 冷熱循環特性試驗 (HEAT CYCLE TEST) PRIOR TO RESISTANCE TESTING， THE SPECIMEN SHALL BE PROCESSED AS FOLLOWING PROCEDURE. 1)A CYCLE OF (40177。 50 ％ 。2) ℃ 30 MINS FOR 10 TIMES. 2) PUT IN ROOM TEMP. FOR (60177。2)℃ (500177。 PANEL SIZE ︰ 50~450 ㎜。０．１５ ０．３㎜ 177。 177。 板 厚 THE THICKNESS OF THE BOARD 沖孔孔邊到板邊間距 THE CLEARANCE OF THE HOLE WITH THE EDGE OF THE BOARD １．６ ㎜ Ｍｉｎ １．２㎜ １．２ ㎜ Ｍｉｎ １．０㎜ ＜１．２㎜ Ｍｉｎ 板厚 沖床板邊凹槽容許值：Ｍａｘ板厚５０％ 。 ㎜。 Min WIDTH： ㎜。 Min. CLEARANCE TO HOLES： ㎜。 銅箔導體間距Ｍ ｉｎ：０．２㎜ 。０．１５㎜ 。 PUNCHING TOOL AND PUNCHING PROCESS 外型成形最小尺寸：１２０㎜１２０㎜ 。 b)光學點與外型公差範圍177。 ANGLE OF THE INCISION： 30176。 177。 VCUT 跳刀必須預留鋸片旋轉空間：≧１５㎜ 。 2θ 176。2) ℃ (500177。 4) HRS. VARIANCE OF RESISTANCE ON SOLVENT DIPPING MUST BE LESS THAN 177。 5) ℃ FOR 10 SECS ＋ R