【正文】 3）削邊銷中心線與定位板上平面的平行度公差為 。f=。由公式（ 51）n=1000v/π d 可求得此工序鉸刀轉速 n= r/min，參照表 49 所列 Z525 型立式鉆床的主軸轉速 , 取轉速 n=97r/min。粗鉸： IT10。選用支架座底面和 Ф 52mm 孔軸線遼寧工程技術大學課程設計 5 作為精基準同樣是遵循了“基準重合”的原則，因?yàn)樵撝Ъ茉?70mm 軸線方向上的尺寸多以他們作為設計基準，即遵循了“基準統一”原則。 分析零件的技術要求 (1) 零件材料為 HT200。 關鍵詞： 專用夾具 工藝規程 生產類型 最優方案 遼寧工程技術大學課程設計 V Abstract This course design is an important part of teaching ， itis the main contents of a po int of order processing machinery and drilling ho les for fixture design process. This course is designed to plete the production internships, pletion of machinery manufacturing and techno logical foundatio n and other profess ional courses conducted. Students through the curriculum des ign, will learn theory and practice of b ining production, resolved the issue of capacity issues and the initial training, and also do a good job after graduatio n for the des ign and embarked on a prehens ive training for jobs. Through the courses, students in the following areas should be tempered: 1. So that students have developed a point of order of the initial capacity. Can make prehens ive use of machinery manufacturing techno logy and other courses based on the bas ic theories and methods, the right to develop a parts order processing machinery. 2. Fixture with the preliminary design for capacity and improve structural design capacity. 3. Combination of des ign, the application process can be skilled method of calculating the correct conduct of calculatio n, such as technic al parameters, cutting force, cutting power, cutting speed, positioning error, the clamping force, and so on. 4. Further improve access to informatio n, skilled use of Des ign Manual, reference materials, such as the ability. 5. Through the entire process of design, process design so that students will carry out the procedures and methods, and foster independent thinking and the ability to work independently. Key words : appropriation tongs craft rules produce a type superior project 遼寧工程技術大學課程設計 IV 目 錄 一 .支架零件的機械加工工藝規程編制 ..................... 1 支架零件的工藝分析及生產類型的確定 ................ 1 零件用途 ................................................ 1 分析零件的技術要求 ....................................... 1 審查零件的工藝性 ......................................... 2 確定支架的生產類型 ....................................... 2 確定毛坯、繪制毛坯簡圖 ............................ 2 選擇毛坯 ................................................ 2 確定毛坯的尺寸公差和機械加工余量 ........................... 2 ...................................... 4 擬定支架工藝路線 .................................. 4 ...........