【正文】 器 argon welding氬焊 vocabulary for stamping模具專業英語[分享]模具述語 一、入水：gate 進入位：　gate location 水口形式：gate type 大水口：edge gate 細水口： pinpoint gate 水口大小：gate size 轉水口：　switching runner/gate 唧嘴口徑：　sprue diameter 二、流道: runner 熱流道：　hot runner,hot manifold 熱嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圓形流道：round(full/half runner 流道電腦分析：mold flow analysis 流道平衡:runner balance 熱嘴：　hot sprue 熱流道板：hot manifold 發熱管：cartridge heater 探針: thermocouples 插頭：　connector plug 插座： connector socket 密封/封料： seal 三、運水：water line 喉塞：line lpug 喉管：tube 塑膠管：plastic tube 快速接頭：jiffy quick connector plug/socker 四、模具零件：　mold ponents 三板模：3plate mold 二板模：2plate mold 邊釘/導邊：leader pin/guide pin 邊司/導套：bushing/guide bushing 中托司：shoulder guide bushing 中托邊L：guide pin 頂針板：ejector retainner plate 托板：　support plate 螺絲： screw 管釘：dowel pin 開模槽：ply bar scot 內模管位：core/cavity interlock 頂針：　ejector pin 司筒：ejector sleeve 司筒針：ejector pin 推板：stripper plate 縮呵：movable core,return core core puller 扣機（尼龍拉勾）：nylon latch lock 斜頂：lifter 模胚（架）： mold base 上內模：cavity insert 下內模：core insert 行位（滑塊）： slide 鑲件：insert 壓座/斜雞：wedge 耐磨板/油板：wedge wear plate 壓條：plate 撐頭: support pillar 唧嘴： sprue bushing 擋板：stop plate 定位圈：locating ring 鎖扣：latch 扣雞：parting lock set 推桿：push bar 栓打螺絲： 頂板：eracuretun 活動臂：lever arm 分流錐：spure sperader 水口司:bush 垃圾釘：stop pin 隔片：buffle 彈弓柱：spring rod 彈弓:die spring 中托司：ejector guide bush 中托邊：ejector guide pin 鑲針：pin 銷子：dowel pin 波子彈弓：ball catch 喉塞: pipe plug 鎖模塊：lock plate 斜頂：angle from pin 斜頂桿：angle ejector rod 尼龍拉勾：parting locks 活動臂：lever arm 復位鍵、提前回桿：early return bar 氣閥：valves 斜導邊：angle pin 術語：terms 承壓平面平衡：parting surface support balance 模排氣：parting line venting 回針碰料位：return pin and cavity interference ?？偢叱銎C規格：mold base shut hight 頂針碰運水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on Aplate,core direct cut on Bplate. 不準用鑲件： Do not use (core/cavity) insert 用鈹銅做鑲件： use beryllium copper insert 初步（正式）模圖設計：preliinary (final) mold design 反呵：reverse core 彈弓壓縮量：spring pressed length 穩定性好：good stability,stable 強度不夠：insufficient rigidity 均勻冷卻：even cooling 扣模：sticking 熱膨脹：thero expansion 公差：tolorance 銅公(電極）：copper electrode常用塑料英語縮略語[分享]英文簡稱 英文全稱 中文全稱 ABA Acrylonitrilebutadieneacrylate 丙烯腈/丁二烯/丙烯酸酯共聚物 ABS Acrylonitrilebutadienestyrene 丙烯腈/丁二烯/苯乙烯共聚物 AES Acrylonitrileethylenestyrene 丙烯腈/乙烯/苯乙烯共聚物 AMMA Acrylonitrile/methyl Methacrylate 丙烯腈/甲基丙烯酸甲酯共聚物 ARP Aromatic polyester 聚芳香酯 AS Acrylonitrilestyrene resin 丙烯腈苯乙烯樹脂 ASA Acrylonitrilestyreneacrylate 丙烯腈/苯乙烯/丙烯酸酯共聚物 CA Cellulose acetate 醋酸纖維塑料 CAB Cellulose acetate butyrate 醋酸丁酸纖維素塑料 CAP Cellulose acetate propionate 醋酸丙酸纖維素 CE Cellulose plastics, general 通用纖維素塑料 CF Cresolformaldehyde 甲酚甲醛樹脂 CMC Carboxymethyl cellulose 羧甲基纖維素 CN Cellulose nitrate 硝酸纖維素 CP Cellulose propionate 丙酸纖維素 CPE Chlorinated polyethylene 氯化聚乙烯 CPVC Chlorinated poly(vinyl chloride) 氯化聚氯乙烯 CS Casein 酪蛋白 CTA Cellulose triacetate 三醋酸纖維素 EC Ethyl cellulose 乙烷纖維素 EMA Ethylene/methacrylic acid 乙烯/甲基丙烯酸共聚物 EP Epoxy, epoxide 環氧樹脂 EPD Ethylenepropylenediene 乙烯丙烯二烯三元共聚物 EPM Ethylenepropylene polymer 乙烯丙烯共聚物 EPS Expanded polystyrene 發泡聚苯乙烯 ETFE Ethylenetetrafluoroethylene 乙烯四氟乙烯共聚物 EVA Ethylene/vinyl acetate 乙烯醋酸乙烯共聚物 EVAL Ethylenevinyl alcohol 乙烯乙烯醇共聚物 FEP Perfluoro(ethylenepropylene) 全氟（乙烯丙烯）塑料 FF Furan formaldehyde 呋喃甲醛 HDPE Highdensity polyethylene plastics 高密度聚乙烯塑料 HIPS High impact polystyrene 高沖聚苯乙烯 IPS Impactresistant polystyrene 耐沖擊聚苯乙烯 LCP Liquid crystal polymer 液晶聚合物 LDPE Lowdensity polyethylene plastics 低密度聚乙烯塑料 LLDPE Linear lowdensity polyethylene 線性低密聚乙烯 LMDPE Linear mediumdensity polyethylene 線性中密聚乙烯零件英語零件類 punch沖頭 insert入塊(嵌入件) deburring punch壓毛邊沖子 groove punch壓線沖子 stamped punch字模沖子 round punch圓沖子 special shape punch異形沖子 bending block折刀 roller滾軸 baffle plate擋塊 located block定位塊 supporting block for location 定位支承塊 air cushion plate氣墊板 aircushion ejectrod氣墊頂桿 trimming punch切邊沖子 stiffening rib punch = stinger 加強筋沖子 ribbon punch壓筋沖子 reelstretch punch卷圓壓平?jīng)_子 guide plate定位板 sliding block滑塊 sliding dowel block滑塊固定塊 active plate活動板 lower sliding plate下滑塊板 upper holder block上壓塊 upper mid plate上中間板 spring box彈簧箱 springbox ejectrod彈簧箱頂桿 springbox ejectplate彈簧箱頂板 bushing bolck襯套 cover plate蓋板 guide pad導料塊 塑件amp。模具相關英文pre sion molding壓縮成型flash mold溢流式模具plsitive mold擠壓式模具split mold分割式模具cavity型控 母模core模心 公模taper錐拔leather cloak仿皮革shiver飾紋flow mark流痕welding mark溶合痕post screw insert螺紋套筒埋值self tapping screw自攻螺絲striper plate脫料板piston活塞cylinder汽缸套chip細碎物handle mold手持式模具移轉成型用模具encapsulation molding低壓封裝成型射出成型用模具two plate兩極式（模具）well type蓄料井insulated runner絕緣澆道方式hot runner熱澆道runner plat澆道模塊valve gate閥門澆口band heater環帶狀的電熱器spindle閥針spear head刨尖頭slag well冷料井cold slag冷料渣air vent排氣道h=~w=L=3~5mmwelding line熔合痕eject pin頂出針knock pin頂出銷return pin回位銷反頂針sleave套筒stripper plate脫料板insert core放置入子runner stripper plate澆道脫料板guide pin導銷eject rod (bar)（成型機）頂業捧subzero深冷處理three plate三極式模具runner system澆道系統stress crack應力電裂orientation定向sprue gate射料澆口，直澆口nozzle射嘴sprue lock pin料頭鉤銷(拉料桿)slag well冷料井side gate側澆口edge gate側緣澆口tab gate搭接澆口film gate薄膜澆口flash gate閘門澆口slit gate縫隙澆口fan gate扇形澆口dish gate因盤形澆口H=F=1/2t~1/5tT=~diaphragm gate隔膜澆口ring gate環形澆口subarine gate潛入式澆口tunnel gate隧道式澆口pin gate針點澆口~Runner less無澆道(sprue less)無射料管方式long nozzle延長噴嘴方式sprue澆口。 Administration 人事行政部DC Document Center 資料中心QE Quality Engineering 品質工程(部)QA Quality Assurance 品質保證(處)QC Quality Control 品質管制(課)PD Product Department 生產部LAB Labratry 實驗室IE Industrial Engineering 工業工程Ramp。Y Assembly 裝配,組裝MAT39