【正文】 dition analysis, the plastic melt filling analysis, cooling quality analysis, shrink mark analysis, injection pressure analysis. III This design is a mold two cavity three plate mold. Due to the special shape of gargle cup, not directly release, need to set up the side parting mechanism, the mold is through the inclined guide pillar side parting, the mold of each part of the design and calculation. At the same time on cavity important parts to processing technology development and the core of NC machining simulation. This paper gives the detailed design process and assembly drawings. Keywords: tooth glass the note molding side parting Simulation modeling NC machining 目錄 第一章 概述 ..................................................................................................................... 1 模具行業發展的現狀 .......................................................................................... 1 我國模具發展的現狀 .......................................................................................... 1 參數化技術慨述 .................................................................................................. 2 選題目的以及意義 .............................................................................................. 3 第二章 塑件成型工藝性分析 ......................................................................................... 4 漱口杯二維圖 ................................................................................................... 4 結構特征分析及成型工藝性分析 ..................................................................... 5 結構特征分析 ............................................................................................ 5 成型工藝性分析 ....................................................................................... 5 塑件材料的基本性能 ................................................................................ 7 塑料的成型收縮率 ................................................................................... 8 塑件材料的流動性 ................................................................................... 8 第三章 塑件成型工藝及設備 ......................................................................................... 9 注塑成型工藝條件 ............................................................................................. 9 IV 溫度 ........................................................................................................... 9 壓力 ........................................................................................................... 9 時間 ......................................................................................................... 10 注射機型號的確定 ............................................................................................ 10 由公稱注射量選擇注射機 ..................................................................... 10 由鎖模力選擇注射機 ............................................................................. 11 型腔數量以及注射機有關工藝參數的校核 ................................................... 12 型腔數量校核 ......................................................................................... 12 額定注塑量校核 ..................................................................................... 13 額定鎖模力校核 ...................................................................................... 13 額定注塑壓力校核 .................................................................................. 14 安裝尺 寸校核 ......................................................................................... 15 開模行程的校核 ...................................................................................... 16 第四章 注射模具結構設計 ........................................................................................... 18 型腔的確定 ........................................................................................................ 18 制品成型位置及分型面的選擇 ........................................................................ 18 澆注系統設計 .................................................................................................... 18 主流道設計 ............................................................................................. 19 冷料穴的設計 .......................................................................................... 20 分流道設計 .............................................................................................. 21 澆口設計 ................................................................................................. 22 剪切速率的校核 ...................................................................................... 24 排氣系統設計 ......................................................................................... 25 成型零件結構設計 ........................................................................................... 26 凹模結構設計與計算 .............................................................................. 26 型芯結構設計與尺寸計算 ...................................................................... 28 4． 5 模架的選用 ..................................................................................................... 29 型腔側壁以及底板厚度尺 寸 .................................................................. 29 模具高度尺寸的確定 .............................................................................. 30 4． 6 導向與定位機構設計 ..................................................................................... 31 脫模機構的設計 ................................................................................................ 33 頂桿脫模機構設計 .................................................................................. 33 頂桿直徑的確定 ...................................................................................... 33 頂桿導向的確定 ...................................................................................... 34 頂桿的復位 .............................................................................................. 35 側向分型與抽芯機構設計 ..............