50米水泥運輸船的結構設計畢業論文(已修改)
2025-07-04 17:16 本頁面
【正文】 50 米水泥運輸船的結構設計摘 要本次畢業設計是對 50m 水泥運輸船的結構設計，主要分為以下幾個方面來進行設計：一、通過母型船的資料和新船的任務書來確定設計新船的型線圖。因?yàn)樾麓蝿?wù)書要求的主尺度除了船長和型深，其他都相同，而且兩者的差距很小。又因?yàn)楸敬緵]有平行中體，所以通過型線比例的變換來改變型值是可行的，然后利用新的型值表來繪制新的型線圖，并進行了光順與協調。二、利用新的型線圖和母型船的一些資料來做結構計算。結構計算主要是利用規范的計算選取外板、甲板、型材、上層建筑以及其他構件的規格。由于本船船長小于 65 米，不用進行總縱強度的計算，只需取材的剖面模數大于規范要求的最小剖面模數即可，當然為了滿足強度，取材時盡量保守。三、通過型線圖和結構計算書以及母型資料來繪制基本結構圖、典型橫剖面圖和橫艙壁圖。以橫艙壁圖為例，利用型線圖在量取該肋位上的高度和半寬值來確定該橫艙壁的外輪廓，再利用結構計算關于艙壁的板厚和型材規格來繪制骨架，繪制過程中參考母型船資料。其他圖也基本類似，不一一列舉。四、總結設計過程中的一些經驗和遇到的困難，以及解決這些問題的方法，為后續結構設計的提供經驗。本次設計的新船滿足任務書的要求，結構強度的校核也滿足文獻[1]的要求。【關鍵詞】 水泥運輸船；結構設計；規范設計；尺寸確定structure designing of 50 meters cement carrierhuang jianschool of civil engineering architecture and civil engineering，Zhejiang ocean university，zhoushan ，zhejiang 316000[Abstract] The graduation design is a structure design of 50m cement carrier, which is mainly divided into the following several aspects in design: First, confirm to design the lines plan of the new ship according to the parent ship39。s data and new ship39。s TOR. Because the new ship39。s TOR requires the rest of the principal dimensions are the same, except the length and depth, which are also required to have a small gap between these two. And because this ship nearly has no parallel middle body, it is feasible to change lines offsets through copy type transformation, and then draw lines plan using new offsets table. Second, use new lines plan and some information of parent ship to do structural calculation. Structural calculation mainly takes advantages of standard calculation to select shell plating, deck, bar, superstructure and other construction elements39。 specification. Since the length of this ship is less than 65 meters, longitudinal strength39。s calculation is not necessary, just make sure that the section modulus for drawing materials is larger than the smallest section modulus. Of course, in order to satisfy the intensity, when you are drawing materials, it should be as large as possible. Third, design basic construction plan, model body plan and transverse bulkhead plan, by using lines plan, structure calculations and some parent ship data. Now, take drawing transverse bulkhead plan as an example, it uses lines plan on the height and width of lifting this Rib bit to ensure the periphery of transverse bulkhead. Then it uses structural calculation about thickness of plating of bulkhead and bar standard to draw skeleton, with the reference of parent ship during this time. Other plans are similar and they will not be list here one by one. Fourth, summarize some experience and difficulties met during the design process, and methods to solve these problems, in order to rise experience in structural design. The design of a new ship meet mitments requirements, and profiles checking intensity and also satisfy the document [1] requirements.【Keywords】cement carrier。 Structure design。 Standard design。 Size determine目 錄摘 要 ............................................................................................................................I緒 論 ............................................................................................................................11 總體部分 ....................................................................................................................2 設計要求和母型資料 ??????????????????????????????????????????????????????????????????????????????????????2 設計任務書 ????????????????????????????????????????????????????????????????????????????????????????????2 母型船艙室分布情況 ????????????????????????????????????????????????????????????????????????????3 母型船主尺度 ????????????????????????????????????????????????????????????????????????????????????????4 型線生成 ??????????????????????????????????????????????????????????????????????????????????????????????????????????42 結構部分 ....................................................................................................................5 結構規范設計計算 ??????????????????????????????????????????????????????????????????????????????????????????5 外板 ????????????????????????????????????????????????????????????????????????????????????????????????????????5 甲板 ??????????????????????????????????????????????????????????????????????????????????????????????????????10 單層底 ??????????????????????????????????????????????????????????????????????????????????????????????????12 舷側骨架 ??????????????????????????????????????????????????????????????????????????????????????????????14 甲板骨架 ??????????????????????????????????????????????????????????????????????????????????????????????19 船端加強 ??????????????????????????????????????????????????????????????????????????????????????????????24 水密艙壁 ??????????????????????????????????????????????????????????????????????????????????????????????25 主機基座 ??????????????????????????????????????????????????????????????????????????????????????????????31 上層建筑 ??????????????????????????????????????????????????????????????????????????????????????????????31 主要構件匯總 ??????????????????????????????????????????????????????????????????????????????????????????????????????????????51 基本結構圖 ????????????????????????????????????????????????????????????????????????????????????????????????????55 典型橫剖面圖 ????????????????????????????????????????????????????????????????????????????????????????????????55 橫艙壁圖 ????????????????????????????????????????????????????????????????????????????????????????????????????????553 總結與討論 ..............................................................................................................56參考文獻 ......................................................................................................................58外文翻譯 ......................................................................................................................60緒 論我國是水泥生產大國，水泥產量多年居世界第一，運輸水泥的方式也是各種各樣，
環評公示相關推薦
鄂ICP備17016276號-1