催化裂化汽提塔畢業設計(已修改)
2025-01-28 10:11 本頁面
【正文】 本 科 畢 業 設 計 (論 文)催化裂化汽提塔設計Design of FCC Stripper Structure學 院：機械工程學院 專業班級：過程裝備與控制工程 裝備 學生姓名： 學 號： 指導教師： 2013年6月 畢業設計（論文）中文摘要催化裂化汽提塔結構設計摘 要：催化裂化汽提塔是化工設備生產中非常重要的裝置之一。主要用于煉油工業中。本文是對汽提塔的結構設計進行了理論計算，確立了本塔的結構要求，并對其中的一系列問題進行分析，得到了結果。本塔分別對裙座、筒體等等進行設計和校核，并對接管進行了補強設計。將筒體進行分段，以便計算質量載荷。然后將每段的質量集中在各段的中心處，計算出地震載荷，并得到地震彎矩。計算風載荷時再將全塔分段，以便得到風彎矩。結合地震彎矩和風彎矩，得到最大彎矩。并對裙座筒體進行穩定驗算，以及對液壓工況下的強度和穩定性進行校核。設計計算了基礎環和地腳螺栓。結構設計部分，選用合適的吊柱，并對塔盤、降液板、受液盤及溢流堰結構尺寸進行設計。最后，對法蘭和墊片進行校核和計算。關鍵詞：催化裂化；汽提塔；結構設計 畢業設計（論文）外文摘要FCC stripper structure designAbstract:. FCC stripper is one of very important device in the production of chemical equipment. Mainly used in oil refining industry. This paper is the structure design of the stripper is calculated, the structure was established, and a series of problems in the analysis, obtained the result. The utility model were design and check of the skirt, cylinder and so on, and take over the reinforcement design. The cylinder body segment, in order to calculate the mass loading. Then each segment of the lumped mass in each center, calculate the seismic loads, and seismic moment. The calculation of wind load and then the whole tower section, in order to obtain the wind moment. Combined with the seismic moment and the wind moment, to get the maximum bending moment. And check the stability of the skirt cylinder, and the strength and stability of hydraulic condition check. The design and calculation of the foundation ring and anchor bolt. Structure design part, choose the appropriate column, and the tray, downer plate, a liquid disk and overflow weir structure size design. Finally, check and calculation of the flange and gasket.Keywords: Catalytic cracking；Stripper；Structure design 目 錄1引言12設計內容22222344566 裙座驗算部分7789 裙座與塔殼連接焊縫驗算910183
教學教案相關推薦
鄂ICP備17016276號-1