【正文】 ment requirement higher,and investment cost is for in thin coal seam development meet the high general machine of coal mining is very machine of model of coal mining only aim at in thin coal seam meet the high general design and that goes on. The section of the machine of model of coal mining cut department mechanical transmission from 3 level directly tooth transmission and a level pla machine transmission realization,and end level adopts the pla transmission of the floating form of sun to rocker arm configuration with the coal space of increase cylinder and then raising pack coal efficiency。 Key words : Shearer 。 Pla anization III 目 錄 摘 要 ..................................................................................................................... I Abstract ................................................................................................................. II 第 1 章 緒論 ........................................................................................................ 1 采煤機簡介 ........................................................................................... 1 國內外采煤機發展及使用狀況 .......................................................... 2 采煤機在我國的使用情況 ....................................................... 2 采煤機在國外的發展和使用 ................................................... 4 采煤機截割部概述 .............................................................................. 6 設計意義 ............................................................................................... 6 第 2 章 截割部傳動總體設計 ........................................................................... 8 截割部主要設計參數 .......................................................................... 8 總體方案確定 ....................................................................................... 8 截割部電動機的選 .............................................................................. 9 截割部傳動比分配 .............................................................................11 第 3 章 截割部系統傳動設計 ......................................................................... 13 齒輪設計 ............................................................................................. 13 21,zz (惰輪 )齒輪設計與校核 ................................................. 13 3z 大 齒輪設計與校核 ............................................................. 23 54,zz 齒 輪設計與校核 .......................................................... 30 6z (惰輪 )齒輪設計與校核 ...................................................... 40 7z 大 齒輪 設計與校核 ............................................................. 49 1098 zzz ， 一 級 行星齒輪設計與校核 .................................. 56 軸的設計校核及軸承壽命計算 ...................................................... 66 IV Ⅰ軸的設計校核及軸承壽命計算 ........................................ 66 Ⅲ軸的設計校核及軸承壽命計算 ........................................ 71 Ⅳ軸的設計校核及軸承壽命計算 ........................................ 77 行星輪系太陽輪軸的設計校核及軸承壽命計算 ................ 83 一級行星輪軸的設計校核及軸承壽命計算 錯誤 !未定義書簽。 結 論 .................................................................................................................. 91 致 謝 ................................................................................... 錯誤 !未定義書簽。 V CONTENTS Abstract ........................................................ Ⅰ Abstract ........................................................ Ⅱ Chapter 1 Introduction........................................................................................ 1 Introduction 1 Shearer ............................................................................. 1 The development and use status at home and abroad Shearer .............. 2 shearer use in China ..................................................................... 2 Shearer development and use abroad .......................................... 4 Overview shearer cutting unit .............................................................. 6 Design of significance ............................................................................. 6 Chapter 2 driving the overall design of cutting unit ....................................... 8 The main design parameters of cutting unit ........................................... 8 The overall scheme for the ...................................................................... 8 The selection of cutting the Department of Motor................................. 9 The distribution of cutting unit of transmission ratio ...........................11 Chapter 3 Design of the Transmission System of cutting unit ..................... 13 Gear Design............................................................................................ 13 21,zz (idler) gear design and Check.......................................... 13 3z Design and Check large gear ................................................ 23 44,zz Gear Design and Check ................................................... 30 6z (idler) gear design and Check............................................... 40 7z Design and Verification of large gear .................................. 49 1098 , zzz Design and Verification of a plaary gear ............. 56 shaft and bearing life calculation design check ................................... 66 Ⅰ shaft and bearing life calculation design check ................... 66 Ⅲ shaft and bearing life calculation design check ................... 71 VI Ⅳ shaft and bearing life calculation design check ................... 77 Plaary Design of the sun a