【正文】 The pulse high harmonic ponent, resulting in serious waste of power and power factor is low, but as a harmonic current source may interfere with the grid voltage, the propagation along the wire and into the surrounding radiation, electromagic interference. The brightness of the LED depends on the size of the current through itself. For these problems, this paper designed a high efficiency new type LED street lamp intelligent controller, can meet the design requirements. In this paper, the main design requirement is as follows:For these problems, this paper designed a high efficiency new type LED street lamp intelligent controller, can meet the design this paper, the main design requirement is as follows: 1. The design of a flyback type LED street lamp with PFC function constant current driver circuit, replace the boost PFC converter and DC/DC converter in the position of the secondary circuit, which simplifies the circuit structure, improve the use efficiency of LED 2. An LED fault detection circuit design, as long as there is any LED lights to fail, then the circuit can be detected in one hundred and fifty milliseconds and to allow output current levels, ensure the safety of other LED lights work in the current scope, ensure the normal operation of the LED street lamp, prolong its service life. 3. Design an LED brightness detection circuit and temperature detection circuit, when the temperature of the chip is very high to allow current range, at the same time can be a basis of synchronous detection LED brightness and brightness automatically adjust the output brightness of LED lights, which can save energy, and can extend the service life and save money. Keywords: LED street lamp, the temperature detection, brightness detection, switch control, constant current control 5 目 錄 摘 要 ......................................................................................................................................... III ABSTRACT ............................................................................................................................. IV 第 1 章 LED 路燈概述 ........................................................................................................ 6 LED 路燈的發展前景 .................................................................................................. 6 LED 驅動電源特點及介紹 ......................................................................................... 6 單片機 ............................................................................................................................ 7 第 2 章 LED 驅動電源原理 ............................................................................................ 9 電源控制技術的發展方向 ....................................................................................... 9 開關電源的分類 ........................................................................................................... 9 調制式（ PWM） 開關電源的原理 ........................................................................... 10 PFC 控制芯片 L6562 ................................................................................................. 12 反饋環路設計原理 ................................................................................................... 13 第 3 章 硬件電路的設計 ................................................................................................. 15 系統總方案的設計 .................................................................................................... 15 EMI 抑制電路和浪涌保護的設計 ......................................................................... 16 溫度檢測電路的設計 ............................................................................................... 17 亮度檢測電路 ............................................................................................................. 17 萬年歷芯片和外圍電路 ........................................................................................... 18 LED 故障檢測電路 .................................................................................................... 16 電 流控制電路 ............................................................................................................ 17 第 4 章 軟件設計 .............................................................................................................. 21 系統軟件設計 ............................................................................................................ 21 亮度檢測軟件設計 ................................................................................................... 22 溫度控制軟件設計 .................................................................................................... 23 故障檢測軟件設計 .................................................................................................... 24 結 論 ......................................................................................................................................... 25 參考文獻 ................................................................................................................................... 28 致 謝 ......................................................................................................................................... 29 6 第 1章 LED 路燈概述 LED 路燈的發展前景 LED 是一個非常實用的新產品，現在是科學家聚焦的一個熱點。下面我們來說說 LED 路燈。 LED 光源不能匆匆應用到路燈照明有幾個因素：第一個就是 LED 發展還不久發展還不是很成熟。第三個就是 LED 還沒有一個比較完善的智能控制電路，可靠性太低。第五就是 LED 還沒有一個國際統一的標準，各個公司的產品不能進行相互之間的調換，維修比較困難，成本比較高。第三就是對于大功率 LED 燈的宣傳一定要謹慎，不能過于夸張，我們要把我們的能量集中在 LED路燈系統的研發工作上面。 LED 路燈有幾個關鍵的技術指標，分別是效率、光型、光衰、壽命。第二就是一些部門的思維太過于固執，還缺乏一些關于 LED 了燈的配套的措施與政策，大家對于 LED 的認識有一個漸漸的過程，這其中包括一些科學家的認識也是經歷從無到有的過程。當然這需要我們對于科研孜孜不倦的追求。它的性能主要有以下幾個方面： 第一， 高性能的驅動電源就會給整個 LED 帶來很高的效率，而效率的提高 能夠節省我們國家的能源，這正是我們國家急需解決的問題。 第三， 因為驅動電源的性能比較好，靈敏度非常高，所以能夠改變 LED 燈的工作方式，使它滿足各種照明的需求，所以可 以根據環境的不同、時間的不 7 同，實時的改變驅動電源燈電流輸出。 LED 元件對驅動電源的技術要求非常的嚴格。在國際的市場上對于 LED的驅動電源的轉化效 率，有效功率，電