【正文】 ●T6963C的字符編碼是ASCII碼不同。發送兩個以上的數據在一個機器周期，這是不可能的。當一個命令被執行時，可能會發生數據傳輸錯誤。有一個硬中斷，由于操作錯誤的可能性。●狀態發送數據或命令之前，必須檢查。 （其它寄存器不會清零。●暫停功能包括復位功能?！癞?dāng)HALT L時，振蕩停止。在雙LSCP =移位時鐘為L(zhǎng)CD下半部的列驅動器的脈沖輸出CE輸出芯片，使顯示存儲器的任何地址引腳D0至D7 I / O數據顯示內存的I / O引腳AD0至AD15輸出顯示存儲器的地址輸出 （AD15 = M：= H AD15液晶，上層面積：較低的液晶顯示屏的面積）功能定義●接通電源后，它是必要的重置。以）雙輸入 DSPON是大號。行驅動器，移位時鐘脈沖FR輸出幀信號第十一輸入晶體振蕩器輸入XO輸出晶體振蕩器輸出CH1，CH2，輸出檢查信號T1 T2輸入測試輸入。文字和圖形的地址和文字和圖形區域設置將被保留。WR輸入WR = C / D =高：命令寫的C / D = L：數據寫入 西鐵= C / D = H：讀狀態的C /240。讀取數據fromT6963C當RD = LCE輸入芯片為T(mén)6963C的啟用。引腳分配和功能管腳名稱I / O功能FS0輸入H：58字體大號：58字體D0的D7 I / O數據的I / O引腳之間的CPU和T6963C的（D7是最高位）WR輸入數據寫入。屬性功能只能在文本模式下使用。 T6963C的不能刷新的DRAM。外部電容晶振：20至30 pF的 陶瓷振蕩：30到100 pF的 內置反饋電阻：900 K？ （典型值）東芝液晶驅動LSI的（其他比這些內置在RAM）可以連接到該設備。如果使用外部時鐘，使用XI引腳的時鐘輸入。從CPU讀或?qū)懖僮鞑淮驍_顯示。顯示稅：1/16至1/128一個128字的字符發生器ROM（代碼0101）的T6963C0101建造的標準。漢字字庫 橫向點數：5，6，7，8 垂直點數：8（固定） 這是必要的，就像在文本模式下設置字符字體在圖形模式。它可用于在文本，圖形，文字和圖形組合模式，包括各種屬性的功能。文本，圖形和外部字符發生器RAM的分配可以輕松顯示窗口可分配的內存范圍內自由移動。它可以直接連接到川芎嗪80。 graphic display is automatically disabled. However, the Display Mode mand must be used to turn both Text and Graphic on in order for the Attribute function to be available. The attribute data for each character in the text area is written to the same address in the graphic area. a) Combination of text / graphic displayb) b) Attribute function 中文翻譯A :T6963C英文資料（節選） 芯片介紹 東芝CMOS數字集成電路硅單片 T6963C的點陣液晶顯示控制LSIT6963C的LCD控制器設計用于LCD控制驅動器LSI和數據顯示記憶。LSCP at DUAL= L Shift clock pulse output for column drivers in lower area of LCD ce Output Chip enable pin for display memory of any address d0 to d7 I / O Data I / O pins for display memory ad0 to ad15 Output Address outputs for display memory (ad15 = L: for upper area of LCD, ad15 = H: for lower area of LCD)Functional Definition ● After power on, it is necessary to reset. RESET is kept L between 5 clocks up. ● When HALT L, the oscillation stops. The power supply for the LCD must now be turned off, to protect the LCD from DC bias. ● The HALT function includes the RESET function. ● The column / line counter and display register are cleared by RESET. (Other registers are not cleared.) Disable the display using the cleardisplay register. ● The status must be checked before data or mands are sent. The MSB 0 status check must be done in particular. There is a possibility of erroneous operation due to a hard interrupt. ● STA0 and STA1 must be checked at the same time. When a mand is executed, data transmission errors may occur. ● The T6963C can only handle one byte per machine cycle (16 clocks). It is impossible to send more than two data in a machine cycle. ● When using a mand with operand data, it important to send the data first, and then execute the mand. ● The character codes used by the T6963C are different from ASCII codes. LCD screen and the MPU data municationFlowchart of munications with MPU (1) Status Read A status check must be performed before data is read or written. Status check The Status of T6963C can be read from the data lines. RD L WR H CE L C / D H D0 to D7 Status word The T6963C status word format is as follows: STA0 Check mand execution capability 0: Disable 1: EnableSTA1 Check data read / write capability 0: Disable 1: EnableSTA2 Check Auto mode data read capability 0: Disable 1: EnableSTA3 Check Auto mode data write capability 0: Disable 1: EnableSTA4 Not used STA5 Check controller operation capability 0: Disable 1: EnableSTA6 Error flag. Used for Screen Peek and Screen copy mands. 0: No error 1: ErrorSTA7 Check the blink condition 0: Display off 1: Normal displayNote 1: It is necessary to check STA0 and STA1 at the same time. There is a possibility of erroneous operation due to a hardware interrupt. Note 2: For most modes STA0 / STA1 are used as a status check. Note 3: STA2 and STA3 are valid in Auto mode。 DualScan SDSEL Input H : Sending data by odd / even separation L:Sending data by simple serial methodce0 Output ce0 at DUAL = H Chip enable pin for display memory in the address range 0000H to 07FFH 。 SingleScan L [9]21IC電子網.外文A: The the T6963C English Data (excerpt) Chip introduced TOSHIBA CMOS DIGITAL INTEGRATED CIRCUIT SILICON MONOLITHIC T6963C DOT MATRIX LCD CONTROL LSI The T6963C is an LCD controller designed to be used with LCD control driver LSIs and data display memories. The device has an 8bit parallel data bus and control lines for reading or writing through an MPU interface. It can be directly connected to a TMPZ80. It has a 128word character generator ROM which can control an external display RAM of up to 64 Kbytes. Allocation of text, graphics and external character generator RAM can be made easily and the display window can be moved freely within the allocated memory range. The device supports a very broad range of LCD formats by allowing selection of different binations via a set of programmable inputs. It can be used in text, graphic and bination textandgraphic modes, and includes various attribute functions. Features Display format (pinselectable) Column