【正文】 處理方法：按下數控系統的紅色 停止鍵，停止回參考點，重新連結校正好光柵尺的連結板，再進入 自動或 半自動模式工作狀態，重新回參考點，排除故障。 ② 油泵電機電流太大，主要可能是高壓濾芯嚴重堵塞。 DNC600 參數簡要說明 01 CLOSED LOOP 閉環 典型值 1 03 FINAL APPROACH DISTANCE 最終接近距離 典型值 05 DECEL RAMP THRESHOLD 減速斜坡起始 典型值 2 06 LOW SPEED THRESHOLD 低速起始 典型值 3 07 MINIMUM LIMIT 最小限位 典 型 值BDC+5mm 10 SYNCHR LIMIT Y 同步限位 典型值 10 11 FA DIST. TDC Y^ 最終接近上死點距離 典型值 3 12 DECEL. THRESHOLD HIGH SPEED 高速減速距離 典型值 7 13 MAX SPEED (mm/s) 最大速度 典型值 10 17 MAX TDC ABOVE INDEX 參考點上最大上死點 默認值 0 ?????????????????????????????????????????????? ? BEAM PARAMETERS 01 0 ?去 ? ? ? 01 CLOSED LOOP 1 ? ? 03 FINAL APPROACH DISTANCE ? ? 05 DECEL RAMP THRESHOLD ? ? 06 LOW SPEED THRESHOLD ? ? 07 MINIMUM LIMIT ? ? 10 SYNCHR LIMIT Y ? ? 11 FA DIST. TDC Y^ ? ? 12 DECEL. THRESHOLD HIGH SPEED ? ? 13 MAX SPEED (mm/s) PV V 10 PV ^ 10 ? ? 17 MAX TDC ABOVE INDEX ? ? 18 CORRECTION FACTOR CP ___ ___ ___ ? ? 19 CORRECTION RANGE CP ? ? ? 1A MEASUREMENT TOLERANCE CP(% TH) __ ? ? 1B SEPARATE CORRECTION CP ? _ ? 20B FA VOLTAGE 最終電壓 典型值 21 LS VOLTAGE 慢速電壓 典型值 4 23 HS DECEL 高速減速電壓 典型值 3 24 HS VOLTAGE 高速電壓 典型值 7 25 VOLTAGE DECOMPRESSION 減壓電壓 26 SYNCHR GAIN 同步增溢 29 INVERTED COUNTING DIR 倒轉計數方向 ? BEAM PARAMETERS 02 0 ? ? ? ? 20 OFFSET Y1 Y2 ? ? 20A MIN VOLTAGE Y1 Y2 ? ? 20B FA VOLTAGE V FA ^ ? ? 21 LS VOLTAGE V LS ^ ? ? 23 HS DECEL V. V HS V ? ? 24 HS VOLTAGE ^ INDEX ? ? 25 VOLTAGE DECOMPRESSION ? ? 26 SYNCHR GAIN HSV __ ^ __ BDC (250) ___ ? ? 28 AUTO OFFSET _ ? ? 29 ENCODER/DISPLAY RESOL / ? ? INVERTED COUNTING DIR. Y1 _ Y2 _ ? 38 DESC RAMP DIST ACC/DEC ASC RAMP DIST ACC/DECEL 下降加減速距離 上升加減速距離 45 SWITCH TIME HS LS (s) 快慢速轉換時間 典型值 45B PRESSURE DELAY HS LS (s) 快慢速壓力延時 46 REGULATION DELAY (s) 調整延時 典型值 47 SERVOVALVE DELAY (s) 伺服閥延時 典型值 48 DECOMPRESSION TIME 減壓時間 典型值 ?????????????????????????????????????????????? ? BEAM PARAMETERS 03 0 ? ? ? ? 37 CORRECTION CP ? ? CORRECTION BDC ? ? CORRECTION BDC AT MAX PRESS. ? ? 38 DESC RAMP DIST ACC/DEC ? ASC RAMP DIST ACC/DECEL ? 39 END OF BEND BEFORE PRESSURE _ ? ? 40 PINCH POINT BEFORE RETRACTION _ ? ? 45 SWITCH TIME HS LS (s) ? ? 45B PRESSURE DELAY HS LS (s) ? ? 46 REGULATION DELAY (s) ? ? 47 SERVOVALVE DELAY (s) ? ? 48 DECOMPRESSION TIME MIN: MAX: ? ? 49 DETECTION STOP Y IMP (400 ms) __ ? ? 49B ENCODER SURVEILLANCE TIME ? ?????????????????????????????????????????????? 60 STARTING POINT AXES/AF 軸啟動點 典型值 3/ ?????????????????????????????????????????????? ? BEAM PARAMETERS 04 0 ? ? ? ? 53 TDC MINIMUM ? ? BENDING AID ? ? 54 DIST START AF BEF. PINCH PT. ? ? 55 BEAM DELAY IF BENDING AID (s) ? ? ? ? 60 STARTING POINT AXES/AF _/_ ? ? 61 AXES START BEFORE/AFTER AF _ ? ? 62 UPSTROKE BEAM ? _ ? ?????????????????????????????????????????????? ? SAFETY PARAMETERS 01 0 ? ? ? ? 41 RETURN TDC SAFETY _ ? ? 42 EXTERNAL SAFETY _ ? ? 42B SAFETY POINT TOLERANCE ? ? 43 MAT/DIE SAFETY DISTANCE ? ? ? ? 231 X POSITION FOR SAFETY SPEED ? ? 232 AXES SPEED IN SAFETY ZONE ? ? 233 X POS FOR DIE RELEASE ? ? ? ?????????????????????????????????????????????? ? SAFETY PARAMETERS 02 0 ? ? ? ? 50 SAFETY DIST. DIE X R ? ? 95 TREATMENT ERROR JITTER 1 ? ? 260 CYCLE BLOKING AT Q REACHED (1=YES) _ ? ? 310 THICKNESS PROBES STOP X (mm) ? ? 311 END OF CYCLE AFTER DELAY ? _ ? ? ? ? 250 POSITIONS F. BACKGAUGE MANUAL TUNING ? ? X R FA ___ ? ?????????????????????????????????????????????? ? DOUBLE SAFETY PARAMETERS 0 ? ? ? ? 41 RETURN TDC SAFETY _ ? ? 42 EXTERNAL SAFETY _ ? ? 42B SAFETY POINT TOLERANCE ? ? 43 MAT/DIE SAFETY DISTANCE ? ? ? ? 231 X POSITION FOR SAFETY SPEED ? ? 232 AXES SPEED IN SAFETY ZONE ? ? 233 X POS FOR DIE RELEASE ? ?????????????????????????????????????????????? 150 PRESSURE 壓力比 157 REEF POSITION 參考位置 158 AXES POSITION 軸位置 159 INDEX POSITION 參考點位置 ?????????????????????????????????????????????? ? CALIBRATION PARAMETERS 0 ? ? ? ? 150 PRESSURE P 0% ___ P 25% ___ ? ? P 50% ___ P 75% ___ ? ? P 10