【正文】 M Card Endurance Test驗證手機長期插拔SIM卡對相關器件的影響。Validate the influence of the correlation parts under the handset to insert and unplug SIM Card longterm.按正常步驟，插入SIM卡，然后取下SIM卡，如此反復安裝。然后，每插拔100次，按外觀結構→開機功能測試順序進行檢查。至1500次時，每50次檢查一次。試驗次數：2000次。Insert and unplug battery as one cycle, repeat do this operation,check the samples as appearance amp。 structure→function test every 100 times, and every 50 times to inspe3PCS試驗后SIM卡扣無變形松動，SIM卡觸片無下陷及變形等外觀不良After test, the SIM card button no distortion, SIM card connctor no sink and distortion and no the same appearance defects.Charger I/O Endurance Test驗證手機長期插拔充電器對相關器件的影響。Validate the charger I/O endurance effect to the relation ponents.被測樣機不包裝、處于通電待機狀態，按正常步驟，插拔充電器插頭。按外觀結構檢查→充電功能測試順序進行。每插拔100次檢查充電功能是否正常，試驗次數：3000次。The samples unpacked and power on, As normal steps to insert and unplug the charger. Inspect order as: appearance amp。 structure→charge function。 Inspect the charge function whet3PCS插拔壽命至少為3000次，必須通過充電功能測試。插頭、插座無變形、無損傷，無接觸不良.Insert and unplug 3000 cycles at least, Charger function test is OK. plug and socket no distortion, damage and any contact NG.USB data cable Endurance Test驗證手機長期插拔USB數據線對相關器件的影響。 Inspect the USB data cable endurance effect to the relation ponent.被測樣機不包裝、處于通電待機狀態，按正常步驟，插拔USB數據線。每插拔100次檢查下載功能是否正常，試驗次數：3000次。The samples unpacked and power on, As normal steps to insert and unplug the USB data cable. Inspect the download function whether normal or not every 100 times. 3000 times in all.3PCS插拔壽命至少為3000次，必須通過下載功能測試。插頭、插座無變形、無損傷，無接觸不良.Insert and unplug 3000 cycles at least, download function test is OK. plug and socket no distortion, damage and any contact NG.25彎曲實驗Bend endurance test檢查手機抗彎曲能力。 check the resistance of mobile phone when it is subjected to bend.將電池裝在機器上，開機狀態下，在手機兩端向內10mm外，用金屬圓棒支撐住。然后，用φ10mm金屬棒以10Kg的力按壓手機表面和背面中央或手機最薄處，按壓時間為5秒/次，共做50次；施力位置為手機的中央。LCD除外。The handset with battery and power on, Hold the handsets with metal stick inside 10mm of the handsets. Then press the face of handsets and center2PCS結構、性能（功能）方面無異常；試驗過程中不能出現自動關機現象。The structure and performance(function) are normal。 Auto power off is unacceptable during the test.26電池裝著沖擊實驗Shoking With Battery Test檢測電池裝配在手機上抗連續滑落的能力。check the resistance of battery assemble on the handset to resist a series of sliding tests.將電池裝在手機中，待機狀態：使手機水平傾斜75度，從10cm處落到硬質電木板上，共計20次。The handset with battery and power on, drop from 10cm high and 75176。 incline to the horniness bakelite board, 20 times in all.5PCS電池不能脫落，手機不能切斷電源；試驗后手機、電池?zé)o破損現象。The battery can39。t be fell off, the handset can39。t be shut off power。 The handset and battery no disrepair defect after test.27開關機穩定性實驗power on/off stability test驗證手機長期開關機對相關器件的影響。validate the influence of the correlation parts under the handset to power on/off longterm.在正常使用的條件下，對電源開關做1000次開關操作。power on, and then power off as one time. Do the operation 1000 times under normal using.2PCS每次開機后能在“要求的時間”內正確讀取SIM卡，能正常搜索到網絡；關機時屏幕無閃爍；無其他異常情況。Can right read the SIM card information within stated time, can normal search network after each power on. Screen no sparkling when power off, and no anothers abnormity.28吊帶拉力實驗 Neck strap pulling test驗證吊帶孔結構強度Validate the performance of the handsets neck strap intensity.拉住吊繩的尾端，靜力50N，持續10秒，進行3次。Draw the end of the neck strap in 50N for 10 second, do the operation 3times.3PCS外觀良好，整體不松脫Appearance is all right, The whole no loose.29視窗沖擊實驗Window Impact Test驗證手機視窗的抗沖擊性能Validate the capacity of the LCD to resist impact.所有機型的外屏：；翻蓋機內部（主屏）：. J for external displays (all products) J for internal displays (clam shell products)4PCSLCD顯示正常，手機功能使用正常LCD display normally, function must be OK.30視窗平壓實驗Window press endurance test驗證手機視窗的抗壓性能。Validate the capacity of the LCD to resist pressure.以直徑8mm的鋼棒，垂直方向以5 kg的力平壓視窗3次，每次持續5秒。主子屏均要進行Use the steel stick as 8mm diameter, press speed is , press the LCD vertically for 5 second, 3 times in all. Both the main LCD and sub LCD are do these operations.3PCSLCD顯示正常，手機功能使用正常LCD display normally, function must be OK.31正面平壓實驗Obverse press endurance test驗證手機的抗壓性能。Validate the capacity of the handsets to resist pressure.被測樣機處插卡開機狀態，將直徑30mm的鋼棒，垂直方向以25 kg的力正面平壓手機各面（除I/O面和天線面），持續10秒，每面3次，受力均勻The handsets power on with SIM card, use the steel stick as 30mm diameter, press each face of the handsets vertically (except I/O and antenna face) in 25kg for 10 second, each face 33PCS外觀良好，且功能使用正常Appearance and function must be normal.32針刺實驗pin stick test用1mm金屬棒檢查手機內部防護性和安全性Inspect the defend and security performance of the inner of handsets with metal stick 1mm diameter.1PCS外觀良好，且功能使用正常，無危險存在Appearance and function is normal. No dangerous.專項實驗 Specified performance33SPEAKER壽命實驗Speaker endurance test驗證手機Speaker的壽命Validate the lifetime of the speaker.在55177。2℃溫度條件下,將5部實驗樣機設置成長時間不間斷響鈴模式,實驗時間72小時，每2小時檢查響鈴情況；在55177。2℃溫度條件下，將5部實驗樣機設置成通話、響鈴+振動的不間斷模式，手機插上充電器，實驗時間72小時，每2小時檢查響鈴情況； 在55177。2℃溫度條件下，將5部實驗樣機長時間不間斷播放Mp3音樂，實驗時間72小時，每2小時檢查情況。在上述過程中，響鈴音量均調至最大。 the 55177。2℃ temperature condition, Setting the 5pcs15PCS實驗樣機SpEAKER工作正常，鈴聲以及樂曲播放時人耳感覺無明顯差異Speaker works normally. No obvious defect for playing ring and Mp3.34馬達振動壽命實驗Motor vibration endurance test驗證手機馬達的壽命Validate the lifetime of the motor.在55177。2℃溫度條件下，將實驗樣機設置成與用戶模式一致，實驗時間不少于72小時。每2小時檢查振動情況Under the 55177。2℃ temperature condition, setting the samples agree user mode, test time is 72 hours. check the vibration every 2hours.5PCS實驗樣機應能正常振動the samples vibrate normally.35GSM手機時鐘維持實驗GSM handsets Clock last test驗證手機內部時鐘在沒有外部電源情況下的維持能力Validate the maintainable capacity of the inner clock under without outer power.將電池裝上實驗樣機充電，充電完成后，校準時間，取下手機大電池，手機放置至規定時間后，檢查手機時間及信息是否有誤。Assemble the battery into the handsets and charge, calibrate the time and take out the battery after charge. After the handsets placed st