【正文】 arks表H203機組安裝找正記錄Alignment record for installation of machine set項目：Project裝置：Unit工號：Section位 號Location No.名 稱Name執行標準Standard for execution項 目Item允許偏差(mm)Tolerance 實際偏差 （mm）Actual deviation標 高Elevation中心線Center line縱 向Longitudinal橫 向Transverse水平測量 (mm/m）Leveling12345678910縱 向Longitudinal允許值Allowable value實測值Measured value橫 向Transverse允許值Allowable value實測值Measured value附圖：Attached diagram承包單位代表Contractor representative施工單位Subcontractor施工人Operator建設單位代表Owner representative檢查員Inspector表H204大型機械灌漿前檢查記錄Inspection record before grouting of large machinery項目：Project裝置：Unit工號：Section位 號Location No.名 稱Name執行標準Standard for execution隱蔽前檢查：Inspection before concealing： 布置□ 接觸面□ 焊接□Shims Layout Contact face Welding□ □Anchoring bolt Bolt hole and foundation surface cleanliness： 平墊鐵 斜墊鐵 Specification of shims Flat shims Tapered shims附圖：Attached diagramNo.hnLNo.hnLNo.hnL 施工人： Operator上項工程經檢查符合設計（規范）要求，可以隱蔽。The above work conforming to the requirement of design (code) may be concealed 年 月 日 Date建設單位代表Owner representative承包單位代表Contractor representative檢查員Inspector表H205機器拆檢及組裝間隙測量記錄Clearance measurement record for disassembling, inspecting and assembling of machine項目：Project裝置：Unit工號：Section位 號Location No.名 稱Name執行標準Standard for execution間隙測量部位Clearance measured location規定值（mm）Specified value拆前間隙（mm）Clearance before disassembling組裝后間隙（mm）Clearance after assembling日期Date注：間隙測量部位另附圖（如果需要）Note: Clearance measured location has diagram attached (if necessary).檢查員Inspector施工人Operator表H206電機空氣間隙測量記錄Air gap measurement record for motor項目：Project裝置：Unit工號：Section位 號Location No.名 稱Name執行標準Standard for execution按定子上標定的一點盤車檢查空氣間隙 單位：（mm）Inspection of air gap at specified point on the stator by idle rotating Unit:部 位Location12345678910111213141516171819實測值Measured value按定子上標定的一點盤車檢查空氣間隙 單位：（mm）Inspection of air gap at specified point on the stator by idle rotating Unit:部 位Location12345678910實測值Measured value承包單位Contractor representative檢查員Inspector施工人Operator表H207機組對中記錄Alignment record of machine set項目：Project裝置：Unit工號：Section位 號Location No.名 稱Name執行標準Standard for execution聯軸器布置簡圖：Diagram of coupler location對中情況：Alignment a1 b1 a4 a2 b4 b2 a3 b3 單位：（mm） Ｕnit 徑向 軸向 Radial Axial聯軸器編號Coupler No.徑 向Radial軸 向Axial端面間隙Clearance at end百分表固定位置Fixed position of dial indicator允許偏差Tolerancea1a2a3a4允許偏差Tolerancea1a2a3a4規定值Stipulated value實測值Measured value備注：Remarks承包單位代表Contractor representative施工單位Subcontractor施工人Operator建設單位代表Owner representative檢查員Inspector表H208 透平試運轉報告Testrun report for turbine項目：Project裝置：Unit工號：Section位 號Location No.機組名稱Name of machine set功 率Power介質名稱Name of medium介質壓力Pressure of mediumMPa介質溫度Temp. of medium℃額定轉速Rated rotational speedr/min試車類別Type of test run試車日期Date of testrun執行標準Standard for execution危急保安器試驗Test of emergency protection device手 動Manual自 動Automatic時間Time轉速Speed (r/min)介 質Medium潤滑油Lubricant軸承溫度Bearing temp. (℃)軸振動（mm）Shaft displacement備注Remarks流量Flow rate溫度Temp. (℃)壓力Pressure(Mpa)溫度Temp. (℃)壓力Pressure(Mpa)前Front后Rear進In出Out進In出Out進In出Out進In出Out