【文章內(nèi)容簡介】 +aaabbbcccddd+ + ef gh ij + ++++++++++++++ 1. row: 6. neighbour information 2. row: 7. neighbour information 3. row: 8. neighbour information 4. row, ef: 6. neighbour information 4. row, gh: 7. neighbour information 4. row, ij: 8. neighbour information aaa carrier number in decimal bbb C1 value, range is 99 99, displayed only in idle mode. Instead of C1 value, letter 39。B39。 and BSIC value will be displayed in active mode. ccc rx level in dBm, minus sign not shown if =100 ddd C2 value, range is 99 99 e,g,i F is shown if cell is in a forbidden location area otherwise location is empty. f,h,j B is Barred, N is normal priority and L is low priority otherwise location is empty. HELP display: 6CH C1 rx C2 7CH C1 rx C2 8CH C1 rx C2 6N 7N 8N  Display 6: Network selection display This display shows the last registered network country code and network code as well as the codes for four forbidden networks and the first 3 preferred networks. ++++++++++++++ +aaabb aaabb+ +aaabb aaabb+ +aaabb aaabb+ +aaabb aaabb+ ++++++++++++++ If three digit MNC is used (DCS1900), display looks different: ++++++++++++++ +aaabbbaaabbb+ +aaabbbaaabbb+ +aaabbbaaabbb+ +aaabbbaaabbb+ ++++++++++++++ 1. row: last registered network 1st forbidden network 2. row: 1st preferred network 2nd forbidden network 3. row: 2nd preferred network 3rd forbidden network 4. row: 3rd preferred network 4th forbidden network aaa country code coded in BCD bbb network code coded in BCD, third digit can be 39。F39。 HELP display: LReg 1_For 1_Pre 2_For 2_Pre 3_For 3_Pre 4_For  Display 7: System information bits for serving cell. ++++++++++++++ +E A H C I BR+ +a b c d e fg+ +ECSC 2Ter MB+ +h i j + ++++++++++++++ a 1 is shown if emergency calls are supported, else 0 b 1 is shown if attachdetachprocedure is allowed, else 0 c 1 is shown if half rate channels are supported, else 0 d 1 is shown if C2 values are broadcasted, else 0 e 1 is shown if system information 7 and 8 are broadcasted, else 0 f 1 is shown if cell broadcast is supported, else 0 g 1 is shown if reestablishment is supported, else 0 The following items are used only in dualband phones: h In idle mode 1 is shown if Early Classmark (ECSC) sending is supported, else 0. In dedicated mode (conversation) X is shown. i In idle mode 1 is shown if 2Ter messages are supported, else 0. In dedicated mode (conversation) X is shown. j MultiBand reporting decimal value (0,1,2,3) is shown if supported. This is shown both in idle and dedicated mode. The following is picked from Phase2+ ETSI GSM version , Section “Additional cell reporting requirements for multi band MS”. For a multi band MS the number of cells, for each frequency band supported, which shall be included in the measurement report is indicated by the parameter, MULTIBAND_REPORTING. The meaning of different values of the parameter is specified as follows: Value Meaning 0 (00) Normal reporting of the six strongest cells, with known and allowed NCC part of BSIC, irrespective of the band used. 1 (01) The MS shall report the strongest cell, with known and allowed NCC part of BSIC, in each of the frequency bands in the BA list, excluding the frequency band of the serving cell. The remaining positions in the measurement report shall be used for reporting of cells in the band of the serving cell. If there are still remaining positions, these shall be used to report the next strongest identified cells in the other bands irrespective of the band used. 2 (10) The MS shall report the two strongest cells, with known and allowed NCC part of BSIC, in each of the frequency bands in the BA list, excluding the frequency band of the serving cell. The remaining positions in the measurement report shall be used for reporting of cells in the band of the serving cell. If there are still remaining positions, these shall be used to report the next strongest identified cells in the other bands irrespective of the band used. 3 (11) The MS shall report the three strongest cells, with known and allowed NCC part of BSIC, in each of the frequency bands in the BA list, excluding the frequency band of the serving cell. The remaining positions in the measurement report shall be used for reporting of cells in the band of the serving cell. If there are still remaining positions, these shall be used to report the next strongest identified cells in the other bands irrespective of the band used. HELP display: